Aluminum EN AC-45100-F vs EN AC-45100-T6
Aluminum · EN AC-45100 temper comparison
EN AC-45100-F and EN AC-45100-T6 are two conditions of the same aluminum grade, EN AC-45100: F (as fabricated) versus T6 (solution heat treated and artificially aged). The chemistry is identical, so every difference below comes from the condition. EN AC-45100-T6 is the stronger of the two: yield strength 215 MPa (31.2 ksi) against 105 MPa (15.2 ksi) for EN AC-45100-F, about 105% more; tensile strength follows at 260 MPa (37.7 ksi) vs 175 MPa (25.4 ksi). In exchange, EN AC-45100-F is the more ductile: elongation 1.5% versus 1.2% for EN AC-45100-T6, and EN AC-45100-T6 is harder (100 HB vs 65 HB).
EN AC-45100-FChoose it when the part is bent, formed or impact-loaded.
EN AC-45100-T6Choose it when strength drives the design.
EN AC-45100-F vs EN AC-45100-T6: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 75 GPa10.9 Msi · Shear Modulus 28 GPa4.1 Msi · Bulk Modulus 72 GPa10.4 Msi · Poisson's Ratio 0.33 · Compressive Strength 225 MPa32.6 ksi · Fracture Toughness (K_IC) 17 MPa·√m15.5 ksi·√in · Hardness, Vickers 108 HV
Physical
Density and transition temperatures.
Same in both: Density 2.75 g/cm³0.1 lb/in³ · Melting Point (Solidus) 525°C977 °F · Liquidus Temperature 610°C1,130 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 963 J/kg·K0.23 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 22 µm/m·K12.2 µin/in·°F · Latent Heat of Fusion 425 J/g183 BTU/lb · Max Service Temperature (continuous) 200°C392 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 30 % IACS · Electrical Resistivity 5.7×10⁻⁸ Ω·m2.24 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.78 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Same in both: Machinability Rating (AISI 1212 = 100 %) 60% · Weldability 35 / 100 · Formability (cold) 5 / 100 · Castability 80 / 100 · Brazeability / Solderability 20 / 100 · Polishability 48 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 55 MJ/kg23,646 BTU/lb · Embodied Carbon (primary production) 4.2 kg CO₂/kg · Embodied Water 500 L/kg59.9 gal/lb · Typical Recycled Content 80%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
EN AC-45100-F vs EN AC-45100-T6 — frequently asked
Is EN AC-45100-T6 stronger than EN AC-45100-F?
Yes. EN AC-45100-T6 has a typical yield strength of 215 MPa (31.2 ksi) against 105 MPa (15.2 ksi) for EN AC-45100-F — about 105% more. Tensile strength is 260 MPa (37.7 ksi) vs 175 MPa (25.4 ksi).
Which condition does FabDigit quote by default, F or T6?
T6 is the default EN AC-45100 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, EN AC-45100-F or EN AC-45100-T6?
EN AC-45100-T6. Its machinability rates very good (74/100) against good (65/100) for EN AC-45100-F.
Ready to make it?
Upload a CAD file and FabDigit prices the part in EN AC-45100-F and EN AC-45100-T6 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.