Aluminum 7B04-T62 vs 7B04-T7351
Aluminum · 7B04 temper comparison
7B04-T62 and 7B04-T7351 are two conditions of the same aluminum grade, 7B04: T62 (T6, heat treated by the user) versus T7351 (T73, stress relieved by stretching). The chemistry is identical, so every difference below comes from the condition. 7B04-T62 is the stronger of the two: yield strength 460 MPa (66.7 ksi) against 400 MPa (58 ksi) for 7B04-T7351, about 15% more; tensile strength follows at 530 MPa (76.9 ksi) vs 470 MPa (68.2 ksi). 7B04-T62 is harder — 148 HB against 133 HB for 7B04-T7351 — which matters for wear surfaces and threads. 7B04-T7351 runs hotter in service (150°C vs 120°C continuous) and 7B04-T7351 conducts heat better (155 W/m·K vs 130 W/m·K).
7B04-T62Choose it when strength drives the design, or when surface hardness matters.
7B04-T7351Choose it when the part sees heat.
7B04-T62 vs 7B04-T7351: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 71 GPa10.3 Msi · Shear Modulus 27 GPa3.9 Msi · Bulk Modulus 70 GPa10.2 Msi · Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Same in both: Density 2.85 g/cm³0.1 lb/in³ · Melting Point (Solidus) 477°C891 °F · Liquidus Temperature 635°C1,175 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 960 J/kg·K0.23 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23.4 µm/m·K13 µin/in·°F · Latent Heat of Fusion 390 J/g168 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.83 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 10 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 205 MJ/kg88,134 BTU/lb · Embodied Carbon (primary production) 13 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 5%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
7B04-T62 vs 7B04-T7351 — frequently asked
Is 7B04-T62 stronger than 7B04-T7351?
Yes. 7B04-T62 has a typical yield strength of 460 MPa (66.7 ksi) against 400 MPa (58 ksi) for 7B04-T7351 — about 15% more. Tensile strength is 530 MPa (76.9 ksi) vs 470 MPa (68.2 ksi).
Which condition does FabDigit quote by default, T62 or T7351?
T6 is the default 7B04 condition in the FabDigit quote flow (neither T62 nor T7351). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose 7B04-T62 over 7B04-T7351?
Pick 7B04-T62 when strength drives the design, or when surface hardness matters. Pick 7B04-T7351 when the part sees heat.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 7B04-T62 and 7B04-T7351 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.