Aluminum 710.0-F vs 710.0-T5
Aluminum · 710.0 temper comparison
710.0-F and 710.0-T5 are two conditions of the same aluminum grade, 710.0: F (as fabricated) versus T5 (cooled from hot working and artificially aged). The chemistry is identical, so every difference below comes from the condition. 710.0-T5 is the stronger of the two: yield strength 170 MPa (24.7 ksi) against 125 MPa (18.1 ksi) for 710.0-F, about 36% more; tensile strength follows at 240 MPa (34.8 ksi) vs 205 MPa (29.7 ksi). In exchange, 710.0-F is the more ductile: elongation 6% versus 5% for 710.0-T5, and 710.0-T5 is harder (75 HB vs 60 HB). 710.0-T5 runs hotter in service (150°C vs 120°C continuous).
710.0-FChoose it when the part is bent, formed or impact-loaded.
710.0-T5Choose it when strength drives the design, or when the part sees heat.
710.0-F vs 710.0-T5: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 71 GPa10.3 Msi · Shear Modulus 26.5 GPa3.8 Msi · Bulk Modulus 70 GPa10.2 Msi · Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Same in both: Density 2.81 g/cm³0.1 lb/in³ · Melting Point (Solidus) 600°C1,112 °F · Liquidus Temperature 650°C1,202 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 960 J/kg·K0.23 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23.6 µm/m·K13.1 µin/in·°F · Latent Heat of Fusion 389 J/g167 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.96 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Same in both: Castability 35 / 100 · Brazeability / Solderability 20 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 200 MJ/kg85,985 BTU/lb · Embodied Carbon (primary production) 12 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 60%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
710.0-F vs 710.0-T5 — frequently asked
Is 710.0-T5 stronger than 710.0-F?
Yes. 710.0-T5 has a typical yield strength of 170 MPa (24.7 ksi) against 125 MPa (18.1 ksi) for 710.0-F — about 36% more. Tensile strength is 240 MPa (34.8 ksi) vs 205 MPa (29.7 ksi).
Which condition does FabDigit quote by default, F or T5?
T5 is the default 710.0 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 710.0-F or 710.0-T5?
710.0-T5. Its machinability rates excellent (85/100) against very good (80/100) for 710.0-F.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 710.0-F and 710.0-T5 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.