Aluminum 7076-F vs 7076-T6
Aluminum · 7076 temper comparison
7076-F and 7076-T6 are two conditions of the same aluminum grade, 7076: F (as fabricated) versus T6 (solution heat treated and artificially aged). The chemistry is identical, so every difference below comes from the condition. 7076-T6 is the stronger of the two: yield strength 435 MPa (63.1 ksi) against 180 MPa (26.1 ksi) for 7076-F, about 142% more; tensile strength follows at 500 MPa (72.5 ksi) vs 300 MPa (43.5 ksi). 7076-T6 is harder — 140 HB against 85 HB for 7076-F — which matters for wear surfaces and threads. 7076-F runs hotter in service (150°C vs 120°C continuous) and 7076-F conducts heat better (168 W/m·K vs 148 W/m·K). On the shop floor, 7076-T6 machines more easily (very good vs good) and 7076-F forms better (fair vs poor).
7076-FChoose it when the part sees heat.
7076-T6Choose it when strength drives the design, or when surface hardness matters.
7076-F vs 7076-T6: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 71 GPa10.3 Msi · Shear Modulus 27 GPa3.9 Msi · Bulk Modulus 70 GPa10.2 Msi · Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Same in both: Density 2.8 g/cm³0.1 lb/in³ · Melting Point (Solidus) 475°C887 °F · Liquidus Temperature 635°C1,175 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 960 J/kg·K0.23 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23.6 µm/m·K13.1 µin/in·°F · Latent Heat of Fusion 390 J/g168 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.82 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 10 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 200 MJ/kg85,985 BTU/lb · Embodied Carbon (primary production) 12 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 20%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
7076-F vs 7076-T6 — frequently asked
Is 7076-T6 stronger than 7076-F?
Yes. 7076-T6 has a typical yield strength of 435 MPa (63.1 ksi) against 180 MPa (26.1 ksi) for 7076-F — about 142% more. Tensile strength is 500 MPa (72.5 ksi) vs 300 MPa (43.5 ksi).
Which condition does FabDigit quote by default, F or T6?
T61 is the default 7076 condition in the FabDigit quote flow (neither F nor T6). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 7076-F or 7076-T6?
7076-T6. Its machinability rates very good (70/100) against good (55/100) for 7076-F; for welding the order is 7076-F first (poor, 25/100) then 7076-T6 (poor, 20/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 7076-F and 7076-T6 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.