Aluminum 6070-O vs 6070-T6511
Aluminum · 6070 temper comparison
6070-O and 6070-T6511 are two conditions of the same aluminum grade, 6070: O (annealed) versus T6511 (T6, stress relieved by stretching, minor straightening). The chemistry is identical, so every difference below comes from the condition. 6070-T6511 is the stronger of the two: yield strength 350 MPa (50.8 ksi) against 69 MPa (10 ksi) for 6070-O, about 5.1 times as much; tensile strength follows at 380 MPa (55.1 ksi) vs 145 MPa (21 ksi). In exchange, 6070-O is the more ductile: elongation 20% versus 10% for 6070-T6511, and 6070-T6511 is harder (120 HB vs 35 HB). 6070-O conducts heat better (201 W/m·K vs 172 W/m·K). On the shop floor, 6070-T6511 machines more easily (good vs fair).
6070-OChoose it when the part is bent, formed or impact-loaded.
6070-T6511Choose it when strength drives the design, or when the part is machined in volume.
6070-O vs 6070-T6511: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 69 GPa10 Msi · Shear Modulus 26 GPa3.8 Msi · Bulk Modulus 69 GPa10 Msi · Poisson's Ratio 0.33 · Fatigue Strength (Endurance Limit) 97 MPa14.1 ksi · Fracture Toughness (K_IC) 28 MPa·√m25.5 ksi·√in · Hardness, Vickers 128 HV
Physical
Density and transition temperatures.
Same in both: Density 2.71 g/cm³0.1 lb/in³ · Melting Point (Solidus) 566°C1,051 °F · Liquidus Temperature 649°C1,200 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 900 J/kg·K0.21 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23.5 µm/m·K13.1 µin/in·°F · Latent Heat of Fusion 393 J/g169 BTU/lb · Max Service Temperature (continuous) 150°C302 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.78 V · Corrosion Resistance 58 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Same in both: Machinability Rating (AISI 1212 = 100 %) 200% · Brazeability / Solderability 35 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 200 MJ/kg85,985 BTU/lb · Embodied Carbon (primary production) 12.5 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
6070-O vs 6070-T6511 — frequently asked
Is 6070-T6511 stronger than 6070-O?
Yes. 6070-T6511 has a typical yield strength of 350 MPa (50.8 ksi) against 69 MPa (10 ksi) for 6070-O — about 5.1 times as much. Tensile strength is 380 MPa (55.1 ksi) vs 145 MPa (21 ksi).
Which condition does FabDigit quote by default, O or T6511?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, 6070-O or 6070-T6511?
6070-T6511. Its machinability rates good (65/100) against fair (35/100) for 6070-O; for welding the order is 6070-O first (very good, 75/100) then 6070-T6511 (very good, 70/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 6070-O and 6070-T6511 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.