Aluminum 5456-H111 vs 5456-H32
Aluminum · 5456 temper comparison
5456-H111 and 5456-H32 are two conditions of the same aluminum grade, 5456: H111 (slightly strain hardened) versus H32 (strain hardened and stabilized, quarter hard). The chemistry is identical, so every difference below comes from the condition. 5456-H32 is the stronger of the two: yield strength 255 MPa (37 ksi) against 180 MPa (26.1 ksi) for 5456-H111, about 42% more; tensile strength follows at 352 MPa (51.1 ksi) vs 315 MPa (45.7 ksi). In exchange, 5456-H111 is the more ductile: elongation 20% versus 16% for 5456-H32, and 5456-H32 is harder (90 HB vs 75 HB).
5456-H111Choose it when the part is bent, formed or impact-loaded.
5456-H32Choose it when strength drives the design.
5456-H111 vs 5456-H32: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Shear Modulus
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 71 GPa10.3 Msi · Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Same in both: Density 2.66 g/cm³0.1 lb/in³ · Melting Point (Solidus) 568°C1,054 °F · Liquidus Temperature 638°C1,180 °F
Thermal
How each material carries heat and how hot it can run.
Latent Heat of Fusion
Same in both: Thermal Conductivity 117 W/m·K67.6 BTU/hr·ft·°F · Specific Heat Capacity 900 J/kg·K0.21 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23.9 µm/m·K13.3 µin/in·°F · Max Service Temperature (continuous) 65°C149 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 29 % IACS · Electrical Resistivity 5.9×10⁻⁸ Ω·m2.32 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.87 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Same in both: Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Water
Same in both: Embodied Energy (primary production) 200 MJ/kg85,985 BTU/lb · Embodied Carbon (primary production) 12.5 kg CO₂/kg · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
5456-H111 vs 5456-H32 — frequently asked
Is 5456-H32 stronger than 5456-H111?
Yes. 5456-H32 has a typical yield strength of 255 MPa (37 ksi) against 180 MPa (26.1 ksi) for 5456-H111 — about 42% more. Tensile strength is 352 MPa (51.1 ksi) vs 315 MPa (45.7 ksi).
Which condition does FabDigit quote by default, H111 or H32?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, 5456-H111 or 5456-H32?
5456-H32, by a small margin. Both rate fair for machinability — 50/100 against 43/100 for 5456-H111; for welding the order is 5456-H111 first (excellent, 90/100) then 5456-H32 (excellent, 85/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 5456-H111 and 5456-H32 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.