Steel 1021 vs 1006 vs 1008 vs 1010
Benchmark · 4 materials
Side-by-side benchmark of 4 steel grades.
1021 vs 1006 and 2 more: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Melting Point (Solidus)
Liquidus Temperature
Same in both: Density 7.87 g/cm³0.28 lb/in³
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Min Service Temperature
Same in both: Latent Heat of Fusion 247 J/g106 BTU/lb
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Same in both: Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Castability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | 1021 | 1006 | 1008 | 1010 |
|---|---|---|---|---|
| Sheet metal | Yes | Yes | Yes | |
| CNC machining | Yes | |||
| Default condition | HR | HR | HR | |
| Relative cost | $ Budget | $ Budget | $ Budget | $ Budget |
| Min. machined wall | 0.8 mm | |||
| Best machined surface | Ra 1.6 µm | |||
| AlCrN | Yes | |||
| AlTiN | Yes | |||
| Black Oxide | Yes | Yes | Yes | |
| CVD Al2O3 | Yes | |||
| CVD TiCN | Yes | |||
| CVD TiN | Yes | |||
| Cerakote | Yes | Yes | Yes | |
| Chrome Plating | Yes | Yes | Yes | |
| CrN | Yes | |||
| DLC | Yes | |||
| E-Coating | Yes | Yes | Yes | |
| HVOF Coating | Yes | |||
| Hot-Dip Galvanizing | Yes | Yes | Yes | |
| MoS2 | Yes | |||
| Multilayer CVD | Yes | |||
| Nickel Plating | Yes | Yes | Yes | |
| PTFE Coating | Yes | Yes | Yes | |
| Painting | Yes | Yes | Yes |
They share 9 finishes: Copper Plating, Electroless Nickel (EN), Epoxy Coating, Gold Plating, Hard Chrome Plating, Manganese Phosphate, Plasma Spray, Silver Plating, Zinc Phosphate.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1021 and 1006 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.