Aluminum 2618A vs 2007 vs 2017A vs 2030
Benchmark · 4 materials
Side-by-side benchmark of 4 aluminum grades.
2618A vs 2007 and 2 more: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Vickers
Hardness, Rockwell B
Same in both: Poisson's Ratio 0.33 · Fatigue Strength (Endurance Limit) 125 MPa18.1 ksi
Physical
Density and transition temperatures.
Density
Melting Point (Solidus)
Liquidus Temperature
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Same in both: Latent Heat of Fusion 390 J/g168 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Galvanic Potential (seawater, vs SCE)
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Brazeability / Solderability
Polishability
Castability
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Modulus of Resilience
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | 2618A | 2007 | 2017A | 2030 |
|---|---|---|---|---|
| CNC machining | Yes | Yes | Yes | |
| Sheet metal | Yes | Yes | Yes | |
| Default condition | ||||
| Relative cost | $$$$ High | $$$ Premium | $$$ Premium | $$$ Premium |
| Min. machined wall | 0.5 mm | 0.8 mm | 0.5 mm | |
| Best machined surface | Ra 0.8 µm | Ra 0.8 µm | Ra 0.8 µm | |
| Anodizing Type II | Yes | Yes | Yes | |
| Cerakote | Yes | Yes | Yes | |
| Chem Film (Alodine) | Yes | Yes | Yes | |
| DLC | Yes | Yes | Yes | |
| E-Coating | Yes | Yes | Yes | |
| Electropolishing | Yes | Yes | Yes | |
| Hard Anodize Type III w/ PTFE | Yes | Yes | Yes | |
| Hard Anodizing Type III | Yes | Yes | Yes | |
| Nickel Plating | Yes | Yes | Yes | |
| PTFE Coating | Yes | Yes | Yes | |
| Painting | Yes | Yes | Yes | |
| Powder Coating | Yes | Yes | Yes |
They share 4 finishes: Electroless Nickel (EN), Epoxy Coating, Gold Plating, Silver Plating.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 2618A and 2007 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.