Titanium Ti-6Al-4V ELI (AM, F3001)-HIP vs Ti-6Al-4V ELI (AM, F3001)-STA
Titanium · Ti-6Al-4V ELI (AM, F3001) temper comparison
Ti-6Al-4V ELI (AM, F3001)-HIP and Ti-6Al-4V ELI (AM, F3001)-STA are two conditions of the same titanium grade, Ti-6Al-4V ELI (AM, F3001): HIP (hot isostatic pressed) versus STA (solution treated and aged). The chemistry is identical, so every difference below comes from the condition. Ti-6Al-4V ELI (AM, F3001)-STA is the stronger of the two: yield strength 1,050 MPa (152 ksi) against 870 MPa (126 ksi) for Ti-6Al-4V ELI (AM, F3001)-HIP, about 21% more; tensile strength follows at 1,150 MPa (167 ksi) vs 960 MPa (139 ksi). In exchange, Ti-6Al-4V ELI (AM, F3001)-HIP is the more ductile: elongation 17% versus 10% for Ti-6Al-4V ELI (AM, F3001)-STA, and Ti-6Al-4V ELI (AM, F3001)-STA is harder (37 HRC vs 31 HRC).
Ti-6Al-4V ELI (AM, F3001)-HIPChoose it when the part is bent, formed or impact-loaded.
Ti-6Al-4V ELI (AM, F3001)-STAChoose it when strength drives the design.
Ti-6Al-4V ELI (AM, F3001)-HIP vs Ti-6Al-4V ELI (AM, F3001)-STA: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Ti-6Al-4V ELI (AM, F3001)-HIPTi-6Al-4V ELI (AM, F3001)-STA
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 114 GPa16.5 Msi · Shear Modulus 44 GPa6.4 Msi · Bulk Modulus 110 GPa16 Msi · Poisson's Ratio 0.34 · Compressive Strength 1,100 MPa160 ksi · Shear Strength 700 MPa102 ksi · Hardness, Brinell 330 HB
Physical
Density and transition temperatures.
Same in both: Density 4.43 g/cm³0.16 lb/in³ · Melting Point (Solidus) 1,604°C2,919 °F · Liquidus Temperature 1,660°C3,020 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 6.7 W/m·K3.9 BTU/hr·ft·°F · Specific Heat Capacity 560 J/kg·K0.13 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 8.6 µm/m·K4.8 µin/in·°F · Latent Heat of Fusion 370 J/g159 BTU/lb · Max Service Temperature (continuous) 350°C662 °F · Min Service Temperature -253°C-423 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 1 % IACS · Electrical Resistivity 1.71×10⁻⁶ Ω·m67.3 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V · Corrosion Resistance 92 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Same in both: Machinability Rating (AISI 1212 = 100 %) 22% · Weldability 75 / 100 · Formability (cold) 20 / 100 · Brazeability / Solderability 40 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 720 MJ/kg309,545 BTU/lb · Embodied Carbon (primary production) 45 kg CO₂/kg · Embodied Water 500 L/kg59.9 gal/lb · Typical Recycled Content 15%
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Ti-6Al-4V ELI (AM, F3001)-HIP vs Ti-6Al-4V ELI (AM, F3001)-STA — frequently asked
Is Ti-6Al-4V ELI (AM, F3001)-STA stronger than Ti-6Al-4V ELI (AM, F3001)-HIP?
Yes. Ti-6Al-4V ELI (AM, F3001)-STA has a typical yield strength of 1,050 MPa (152 ksi) against 870 MPa (126 ksi) for Ti-6Al-4V ELI (AM, F3001)-HIP — about 21% more. Tensile strength is 1,150 MPa (167 ksi) vs 960 MPa (139 ksi).
Which condition does FabDigit quote by default, HIP or STA?
SR is the default Ti-6Al-4V ELI (AM, F3001) condition in the FabDigit quote flow (neither HIP nor STA). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Ti-6Al-4V ELI (AM, F3001)-HIP or Ti-6Al-4V ELI (AM, F3001)-STA?
Ti-6Al-4V ELI (AM, F3001)-HIP, by a small margin. Both rate poor for machinability — 23/100 against 18/100 for Ti-6Al-4V ELI (AM, F3001)-STA.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Ti-6Al-4V ELI (AM, F3001)-HIP and Ti-6Al-4V ELI (AM, F3001)-STA side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.