Titanium Grade 23 As Printed vs Grade 23 Stress Relieved
Titanium · Grade 23 temper comparison
Grade 23 As Printed and Grade 23 Stress Relieved are two conditions of the same titanium grade, Grade 23: As Printed (as built (as printed)) versus Stress Relieved. The chemistry is identical, so every difference below comes from the condition. Grade 23 As Printed is the stronger of the two: yield strength 1,050 MPa (152 ksi) against 890 MPa (129 ksi) for Grade 23 Stress Relieved, about 18% more; tensile strength follows at 1,150 MPa (167 ksi) vs 970 MPa (141 ksi). In exchange, Grade 23 Stress Relieved is the more ductile: elongation 13% versus 9% for Grade 23 As Printed, and Grade 23 As Printed is harder (38 HRC vs 34 HRC). Grade 23 Stress Relieved runs hotter in service (350°C vs 300°C continuous).
Grade 23 As PrintedChoose it when strength drives the design.
Grade 23 Stress RelievedChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
Grade 23 As Printed vs Grade 23 Stress Relieved: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all titanium grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Grade 23 As PrintedGrade 23 Stress Relieved
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Rockwell C
Hardness, Vickers
Same in both: Shear Modulus 44 GPa6.4 Msi · Bulk Modulus 110 GPa16 Msi · Poisson's Ratio 0.34 · Compressive Strength 970 MPa141 ksi · Shear Strength 580 MPa84.1 ksi · Hardness, Brinell 320 HB
Physical
Density and transition temperatures.
Density
Same in both: Melting Point (Solidus) 1,604°C2,919 °F · Liquidus Temperature 1,660°C3,020 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 6.7 W/m·K3.9 BTU/hr·ft·°F · Specific Heat Capacity 526 J/kg·K0.13 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 8.6 µm/m·K4.8 µin/in·°F · Latent Heat of Fusion 365 J/g157 BTU/lb · Min Service Temperature -253°C-423 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 1 % IACS · Electrical Resistivity 1.71×10⁻⁶ Ω·m67.3 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.1 V · Corrosion Resistance 92 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Same in both: Machinability Rating (AISI 1212 = 100 %) 22% · Weldability 80 / 100 · Formability (cold) 35 / 100 · Castability 40 / 100 · Brazeability / Solderability 35 / 100 · Polishability 80 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 700 MJ/kg300,946 BTU/lb · Embodied Carbon (primary production) 45 kg CO₂/kg · Embodied Water 480 L/kg57.5 gal/lb · Typical Recycled Content 15%
Strength versus weight
Yield strength against density for every titanium grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Grade 23 As Printed vs Grade 23 Stress Relieved — frequently asked
Is Grade 23 As Printed stronger than Grade 23 Stress Relieved?
Yes. Grade 23 As Printed has a typical yield strength of 1,050 MPa (152 ksi) against 890 MPa (129 ksi) for Grade 23 Stress Relieved — about 18% more. Tensile strength is 1,150 MPa (167 ksi) vs 970 MPa (141 ksi).
Which condition does FabDigit quote by default, As Printed or Stress Relieved?
O is the default Grade 23 condition in the FabDigit quote flow (neither As Printed nor Stress Relieved). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose Grade 23 As Printed over Grade 23 Stress Relieved?
Pick Grade 23 As Printed when strength drives the design. Pick Grade 23 Stress Relieved when the part is bent, formed or impact-loaded, or when the part sees heat.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Grade 23 As Printed and Grade 23 Stress Relieved side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.