Steel Y40Mn-IH vs Y40Mn-N
Steel · Y40Mn temper comparison
Y40Mn-IH and Y40Mn-N are two conditions of the same steel grade, Y40Mn: IH (induction hardened) versus N (normalized). The chemistry is identical, so every difference below comes from the condition. Y40Mn-IH is the stronger of the two: yield strength 720 MPa (104 ksi) against 410 MPa (59.5 ksi) for Y40Mn-N, about 76% more; tensile strength follows at 900 MPa (131 ksi) vs 700 MPa (102 ksi). In exchange, Y40Mn-N is the more ductile: elongation 17% versus 12% for Y40Mn-IH, and Y40Mn-N is harder (207 HB vs 195 HB). Y40Mn-N runs hotter in service (425°C vs 200°C continuous). On the shop floor, Y40Mn-N machines more easily (good vs poor) and Y40Mn-N welds better (poor vs not recommended).
Y40Mn-IHChoose it when strength drives the design.
Y40Mn-NChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
Y40Mn-IH vs Y40Mn-N: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.9 µm/m·K6.6 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.61 V · Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 50 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 1.9 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Y40Mn-IH vs Y40Mn-N — frequently asked
Is Y40Mn-IH stronger than Y40Mn-N?
Yes. Y40Mn-IH has a typical yield strength of 720 MPa (104 ksi) against 410 MPa (59.5 ksi) for Y40Mn-N — about 76% more. Tensile strength is 900 MPa (131 ksi) vs 700 MPa (102 ksi).
Which condition does FabDigit quote by default, IH or N?
CD is the default Y40Mn condition in the FabDigit quote flow (neither IH nor N). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Y40Mn-IH or Y40Mn-N?
Y40Mn-N. Its machinability rates good (62/100) against poor (20/100) for Y40Mn-IH; for welding the order is Y40Mn-N first (poor, 28/100) then Y40Mn-IH (not recommended, 12/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in Y40Mn-IH and Y40Mn-N side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.