Steel WC1 A+T vs WC1 Q+T
Steel · WC1 temper comparison
WC1 A+T and WC1 Q+T are two conditions of the same steel grade, WC1: A+T (full annealed and tempered) versus Q+T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. WC1 Q+T is the stronger of the two: yield strength 360 MPa (52.2 ksi) against 275 MPa (39.9 ksi) for WC1 A+T, about 31% more; tensile strength follows at 570 MPa (82.7 ksi) vs 480 MPa (69.6 ksi). In exchange, WC1 A+T is the more ductile: elongation 31% versus 26% for WC1 Q+T, and WC1 Q+T is harder (180 HB vs 149 HB).
WC1 A+TChoose it when the part is bent, formed or impact-loaded.
WC1 Q+TChoose it when strength drives the design.
WC1 A+T vs WC1 Q+T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Compressive Strength 300 MPa43.5 ksi · Shear Strength 340 MPa49.3 ksi · Fracture Toughness (K_IC) 130 MPa·√m118 ksi·√in · Hardness, Vickers 168 HV
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,505°C2,741 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 42 W/m·K24.3 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.2 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 455°C851 °F · Min Service Temperature -29°C-20 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 8.5 % IACS · Electrical Resistivity 2×10⁻⁷ Ω·m7.87 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.61 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Same in both: Weldability 70 / 100 · Formability (cold) 20 / 100 · Castability 70 / 100 · Brazeability / Solderability 55 / 100 · Polishability 50 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 26 MJ/kg11,178 BTU/lb · Embodied Carbon (primary production) 2.1 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 80%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
WC1 A+T vs WC1 Q+T — frequently asked
Is WC1 Q+T stronger than WC1 A+T?
Yes. WC1 Q+T has a typical yield strength of 360 MPa (52.2 ksi) against 275 MPa (39.9 ksi) for WC1 A+T — about 31% more. Tensile strength is 570 MPa (82.7 ksi) vs 480 MPa (69.6 ksi).
Which condition does FabDigit quote by default, A+T or Q+T?
N+T is the default WC1 condition in the FabDigit quote flow (neither A+T nor Q+T). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, WC1 A+T or WC1 Q+T?
WC1 A+T. Its machinability rates good (62/100) against fair (54/100) for WC1 Q+T.
Ready to make it?
Upload a CAD file and FabDigit prices the part in WC1 A+T and WC1 Q+T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.