Steel TRIP600-CR vs TRIP600-HR
Steel · TRIP600 temper comparison
TRIP600-CR and TRIP600-HR are two conditions of the same steel grade, TRIP600: CR (cold rolled) versus HR (hot rolled). The chemistry is identical, so every difference below comes from the condition. TRIP600-HR is the stronger of the two: yield strength 420 MPa (60.9 ksi) against 390 MPa (56.6 ksi) for TRIP600-CR, about 8% more. In exchange, TRIP600-CR is the more ductile: elongation 29% versus 25% for TRIP600-HR, and TRIP600-HR is harder (15 HRC vs 14 HRC).
TRIP600-CRChoose it when the part is bent, formed or impact-loaded.
TRIP600-HRChoose it when strength drives the design.
TRIP600-CR vs TRIP600-HR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 207 GPa30 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 165 GPa23.9 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 7.8 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,450°C2,642 °F · Liquidus Temperature 1,505°C2,741 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 40 W/m·K23.1 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.5 µm/m·K6.9 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 200°C392 °F · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 6.5 % IACS · Electrical Resistivity 2.7×10⁻⁷ Ω·m10.6 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 11 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Same in both: Machinability Rating (AISI 1212 = 100 %) 50% · Brazeability / Solderability 40 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 30 MJ/kg12,898 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 40 L/kg4.8 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
TRIP600-CR vs TRIP600-HR — frequently asked
Is TRIP600-HR stronger than TRIP600-CR?
Yes. TRIP600-HR has a typical yield strength of 420 MPa (60.9 ksi) against 390 MPa (56.6 ksi) for TRIP600-CR — about 8% more. Tensile strength is 640 MPa (92.8 ksi) vs 650 MPa (94.3 ksi).
Which condition does FabDigit quote by default, CR or HR?
CR is the default TRIP600 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose TRIP600-CR over TRIP600-HR?
Pick TRIP600-CR when the part is bent, formed or impact-loaded. Pick TRIP600-HR when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in TRIP600-CR and TRIP600-HR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.