Steel SNB7 Normalized vs SNB7 Q&T 64-100mm
Steel · SNB7 temper comparison
SNB7 Normalized and SNB7 Q&T 64-100mm are two conditions of the same steel grade, SNB7: Normalized versus Q&T 64-100mm (Q&T 64–100 mm dia). The chemistry is identical, so every difference below comes from the condition. SNB7 Q&T 64-100mm is the stronger of the two: yield strength 745 MPa (108 ksi) against 655 MPa (95 ksi) for SNB7 Normalized, about 14% more. SNB7 Q&T 64-100mm is the more ductile: elongation 21% versus 18% for SNB7 Normalized, and SNB7 Normalized is harder (302 HB vs 265 HB).
SNB7 Q&T 64-100mmChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
SNB7 Normalized vs SNB7 Q&T 64-100mm: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
SNB7 NormalizedSNB7 Q&T 64-100mm
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,416°C2,581 °F · Liquidus Temperature 1,495°C2,723 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 473 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -30°C-22 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 35 / 100 · Brazeability / Solderability 55 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 30 MJ/kg12,898 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
SNB7 Normalized vs SNB7 Q&T 64-100mm — frequently asked
Is SNB7 Q&T 64-100mm stronger than SNB7 Normalized?
Yes. SNB7 Q&T 64-100mm has a typical yield strength of 745 MPa (108 ksi) against 655 MPa (95 ksi) for SNB7 Normalized — about 14% more. Tensile strength is 880 MPa (128 ksi) vs 1,020 MPa (148 ksi).
Which condition does FabDigit quote by default, Normalized or Q&T 64-100mm?
Q&T ≤64mm is the default SNB7 condition in the FabDigit quote flow (neither Normalized nor Q&T 64-100mm). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, SNB7 Normalized or SNB7 Q&T 64-100mm?
SNB7 Q&T 64-100mm, by a small margin. Both rate fair for machinability — 50/100 against 45/100 for SNB7 Normalized.
Ready to make it?
Upload a CAD file and FabDigit prices the part in SNB7 Normalized and SNB7 Q&T 64-100mm side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.