Steel Maraging 250 Annealed vs Maraging 250 As Printed
Steel · Maraging 250 temper comparison
Maraging 250 Annealed and Maraging 250 As Printed are two conditions of the same steel grade, Maraging 250: Annealed versus As Printed (as built (as printed)). The chemistry is identical, so every difference below comes from the condition. Maraging 250 As Printed is the stronger of the two: yield strength 950 MPa (138 ksi) against 810 MPa (117 ksi) for Maraging 250 Annealed, about 17% more; tensile strength follows at 1,130 MPa (164 ksi) vs 1,010 MPa (146 ksi). In exchange, Maraging 250 Annealed is the more ductile: elongation 18% versus 12% for Maraging 250 As Printed, and Maraging 250 As Printed is harder (320 HB vs 300 HB). Maraging 250 Annealed is stiffer (181 GPa vs 170 GPa) and Maraging 250 Annealed conducts heat better (25.5 W/m·K vs 20 W/m·K).
Maraging 250 AnnealedChoose it when the part is bent, formed or impact-loaded.
Maraging 250 As PrintedChoose it when strength drives the design.
Maraging 250 Annealed vs Maraging 250 As Printed: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Maraging 250 AnnealedMaraging 250 As Printed
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Shear Modulus 70 GPa10.2 Msi · Bulk Modulus 155 GPa22.5 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Density
Same in both: Melting Point (Solidus) 1,413°C2,575 °F · Liquidus Temperature 1,430°C2,606 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 450 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.1 µm/m·K5.6 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.58 V · Corrosion Resistance 25 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 80 / 100 · Castability 35 / 100 · Brazeability / Solderability 55 / 100 · Polishability 85 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 90 MJ/kg38,693 BTU/lb · Embodied Carbon (primary production) 7 kg CO₂/kg · Embodied Water 130 L/kg15.6 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Maraging 250 Annealed vs Maraging 250 As Printed — frequently asked
Is Maraging 250 As Printed stronger than Maraging 250 Annealed?
Yes. Maraging 250 As Printed has a typical yield strength of 950 MPa (138 ksi) against 810 MPa (117 ksi) for Maraging 250 Annealed — about 17% more. Tensile strength is 1,130 MPa (164 ksi) vs 1,010 MPa (146 ksi).
Which condition does FabDigit quote by default, Annealed or As Printed?
Annealed is the default Maraging 250 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Maraging 250 Annealed or Maraging 250 As Printed?
Maraging 250 Annealed, by a small margin. Both rate fair for machinability — 45/100 against 40/100 for Maraging 250 As Printed.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Maraging 250 Annealed and Maraging 250 As Printed side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.