Steel EN9-CR vs EN9 Normalized
Steel · EN9 temper comparison
EN9-CR and EN9 Normalized are two conditions of the same steel grade, EN9: CR (cold rolled) versus Normalized. The chemistry is identical, so every difference below comes from the condition. EN9-CR is the stronger of the two: yield strength 600 MPa (87 ksi) against 380 MPa (55.1 ksi) for EN9 Normalized, about 58% more; tensile strength follows at 750 MPa (109 ksi) vs 680 MPa (98.6 ksi). In exchange, EN9 Normalized is the more ductile: elongation 16% versus 9% for EN9-CR, and EN9-CR is harder (225 HB vs 200 HB). EN9 Normalized runs hotter in service (380°C vs 300°C continuous).
EN9-CRChoose it when strength drives the design.
EN9 NormalizedChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
EN9-CR vs EN9 Normalized: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 207 GPa30 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 480 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.7 µm/m·K6.5 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 10 % IACS · Electrical Resistivity 1.8×10⁻⁷ Ω·m7.09 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 10 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 45 / 100 · Brazeability / Solderability 55 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
EN9-CR vs EN9 Normalized — frequently asked
Is EN9-CR stronger than EN9 Normalized?
Yes. EN9-CR has a typical yield strength of 600 MPa (87 ksi) against 380 MPa (55.1 ksi) for EN9 Normalized — about 58% more. Tensile strength is 750 MPa (109 ksi) vs 680 MPa (98.6 ksi).
Which condition does FabDigit quote by default, CR or Normalized?
HR is the default EN9 condition in the FabDigit quote flow (neither CR nor Normalized). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, EN9-CR or EN9 Normalized?
EN9-CR. Its machinability rates good (55/100) against fair (50/100) for EN9 Normalized.
Ready to make it?
Upload a CAD file and FabDigit prices the part in EN9-CR and EN9 Normalized side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.