Steel A572-CD vs A572 Normalized
Steel · A572 temper comparison
A572-CD and A572 Normalized are two conditions of the same steel grade, A572: CD (cold drawn) versus Normalized. The chemistry is identical, so every difference below comes from the condition. A572-CD is the stronger of the two: yield strength 470 MPa (68.2 ksi) against 365 MPa (52.9 ksi) for A572 Normalized, about 29% more; tensile strength follows at 560 MPa (81.2 ksi) vs 490 MPa (71.1 ksi). In exchange, A572 Normalized is the more ductile: elongation 24% versus 12% for A572-CD, and A572-CD is harder (180 HB vs 150 HB). A572 Normalized runs hotter in service (425°C vs 350°C continuous). On the shop floor, A572-CD machines more easily (65 vs 55 out of 100).
A572-CDChoose it when strength drives the design, or when the part is machined in volume.
A572 NormalizedChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
A572-CD vs A572 Normalized: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,510°C2,750 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Min Service Temperature
Same in both: Thermal Conductivity 48 W/m·K27.7 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.7 µm/m·K6.5 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 9 % IACS · Electrical Resistivity 1.9×10⁻⁷ Ω·m7.48 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.61 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 60 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 25 MJ/kg10,748 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
A572-CD vs A572 Normalized — frequently asked
Is A572-CD stronger than A572 Normalized?
Yes. A572-CD has a typical yield strength of 470 MPa (68.2 ksi) against 365 MPa (52.9 ksi) for A572 Normalized — about 29% more. Tensile strength is 560 MPa (81.2 ksi) vs 490 MPa (71.1 ksi).
Which condition does FabDigit quote by default, CD or Normalized?
HR is the default A572 condition in the FabDigit quote flow (neither CD nor Normalized). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, A572-CD or A572 Normalized?
A572-CD, by a small margin. Both rate good for machinability — 65/100 against 55/100 for A572 Normalized; for welding the order is A572 Normalized first (excellent, 85/100) then A572-CD (very good, 78/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in A572-CD and A572 Normalized side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.