Steel A352 Grade LC3 DN+T vs A352 Grade LC3 Q+T
Steel · A352 Grade LC3 temper comparison
A352 Grade LC3 DN+T and A352 Grade LC3 Q+T are two conditions of the same steel grade, A352 Grade LC3: DN+T (double normalized and tempered) versus Q+T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. A352 Grade LC3 Q+T is the stronger of the two: yield strength 380 MPa (55.1 ksi) against 345 MPa (50 ksi) for A352 Grade LC3 DN+T, about 10% more; tensile strength follows at 570 MPa (82.7 ksi) vs 540 MPa (78.3 ksi). A352 Grade LC3 Q+T is harder — 175 HB against 163 HB for A352 Grade LC3 DN+T — which matters for wear surfaces and threads.
A352 Grade LC3 Q+TChoose it when strength drives the design, or when surface hardness matters.
A352 Grade LC3 DN+T vs A352 Grade LC3 Q+T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
A352 Grade LC3 DN+TA352 Grade LC3 Q+T
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 78 GPa11.3 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Reduction in Area 55%
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 36 W/m·K20.8 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.5 µm/m·K6.4 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 340°C644 °F · Min Service Temperature -101°C-150 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.2 % IACS · Electrical Resistivity 2.4×10⁻⁷ Ω·m9.45 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.61 V · Corrosion Resistance 15 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 70 / 100 · Brazeability / Solderability 45 / 100 · Polishability 50 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 24 MJ/kg10,318 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 45 L/kg5.4 gal/lb · Typical Recycled Content 80%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
A352 Grade LC3 DN+T vs A352 Grade LC3 Q+T — frequently asked
Is A352 Grade LC3 Q+T stronger than A352 Grade LC3 DN+T?
Yes. A352 Grade LC3 Q+T has a typical yield strength of 380 MPa (55.1 ksi) against 345 MPa (50 ksi) for A352 Grade LC3 DN+T — about 10% more. Tensile strength is 570 MPa (82.7 ksi) vs 540 MPa (78.3 ksi).
Which condition does FabDigit quote by default, DN+T or Q+T?
N+T is the default A352 Grade LC3 condition in the FabDigit quote flow (neither DN+T nor Q+T). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, A352 Grade LC3 DN+T or A352 Grade LC3 Q+T?
A352 Grade LC3 DN+T. Its machinability rates good (55/100) against fair (50/100) for A352 Grade LC3 Q+T.
Ready to make it?
Upload a CAD file and FabDigit prices the part in A352 Grade LC3 DN+T and A352 Grade LC3 Q+T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.