Steel A352 Grade LC2 N+T vs A352 Grade LC2 Q+T
Steel · A352 Grade LC2 temper comparison
A352 Grade LC2 N+T and A352 Grade LC2 Q+T are two conditions of the same steel grade, A352 Grade LC2: N+T (normalized and tempered) versus Q+T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. A352 Grade LC2 Q+T is the stronger of the two: yield strength 400 MPa (58 ksi) against 340 MPa (49.3 ksi) for A352 Grade LC2 N+T, about 18% more; tensile strength follows at 580 MPa (84.1 ksi) vs 530 MPa (76.9 ksi). A352 Grade LC2 Q+T is harder — 180 HB against 160 HB for A352 Grade LC2 N+T — which matters for wear surfaces and threads.
A352 Grade LC2 Q+TChoose it when strength drives the design, or when surface hardness matters.
A352 Grade LC2 N+T vs A352 Grade LC2 Q+T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
A352 Grade LC2 N+TA352 Grade LC2 Q+T
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 78 GPa11.3 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Compressive Strength 345 MPa50 ksi · Shear Strength 350 MPa50.8 ksi · Fracture Toughness (K_IC) 120 MPa·√m109 ksi·√in
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 38 W/m·K22 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.9 µm/m·K6.6 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -73°C-99 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 15 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability Rating (AISI 1212 = 100 %)
Same in both: Machinability 50 / 100 · Weldability 65 / 100 · Formability (cold) 10 / 100 · Castability 70 / 100 · Brazeability / Solderability 55 / 100 · Polishability 50 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 30 MJ/kg12,898 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 75%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
A352 Grade LC2 N+T vs A352 Grade LC2 Q+T — frequently asked
Is A352 Grade LC2 Q+T stronger than A352 Grade LC2 N+T?
Yes. A352 Grade LC2 Q+T has a typical yield strength of 400 MPa (58 ksi) against 340 MPa (49.3 ksi) for A352 Grade LC2 N+T — about 18% more. Tensile strength is 580 MPa (84.1 ksi) vs 530 MPa (76.9 ksi).
Which condition does FabDigit quote by default, N+T or Q+T?
N+T is the default A352 Grade LC2 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose A352 Grade LC2 N+T over A352 Grade LC2 Q+T?
Pick A352 Grade LC2 Q+T when strength drives the design, or when surface hardness matters.
Ready to make it?
Upload a CAD file and FabDigit prices the part in A352 Grade LC2 N+T and A352 Grade LC2 Q+T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.