Steel 9310-CR vs 9310 Q&T
Steel · 9310 temper comparison
9310-CR and 9310 Q&T are two conditions of the same steel grade, 9310: CR (cold rolled) versus Q&T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. 9310 Q&T is the stronger of the two: yield strength 1,100 MPa (160 ksi) against 640 MPa (92.8 ksi) for 9310-CR, about 72% more; tensile strength follows at 1,300 MPa (189 ksi) vs 880 MPa (128 ksi). 9310 Q&T is harder — 363 HB against 255 HB for 9310-CR — which matters for wear surfaces and threads. 9310-CR runs hotter in service (400°C vs 300°C continuous). On the shop floor, 9310-CR machines more easily (fair vs poor), 9310-CR welds better (fair vs poor), and 9310-CR forms better (fair vs not recommended).
9310-CRChoose it when the part sees heat, or when the part is machined in volume.
9310 Q&TChoose it when strength drives the design, or when surface hardness matters.
9310-CR vs 9310 Q&T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Hardness, Rockwell B 98 HRB
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.6 µm/m·K6.4 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -90°C-130 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 6.6 % IACS · Electrical Resistivity 2.6×10⁻⁷ Ω·m10.2 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 14 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 34 MJ/kg14,617 BTU/lb · Embodied Carbon (primary production) 2.5 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
9310-CR vs 9310 Q&T — frequently asked
Is 9310 Q&T stronger than 9310-CR?
Yes. 9310 Q&T has a typical yield strength of 1,100 MPa (160 ksi) against 640 MPa (92.8 ksi) for 9310-CR — about 72% more. Tensile strength is 1,300 MPa (189 ksi) vs 880 MPa (128 ksi).
Which condition does FabDigit quote by default, CR or Q&T?
HR is the default 9310 condition in the FabDigit quote flow (neither CR nor Q&T). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 9310-CR or 9310 Q&T?
9310-CR. Its machinability rates fair (45/100) against poor (25/100) for 9310 Q&T; for welding the order is 9310-CR first (fair, 36/100) then 9310 Q&T (poor, 20/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 9310-CR and 9310 Q&T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.