Steel 7CrMoVTiB10-10 N+T vs 7CrMoVTiB10-10 Q+T
Steel · 7CrMoVTiB10-10 temper comparison
7CrMoVTiB10-10 N+T and 7CrMoVTiB10-10 Q+T are two conditions of the same steel grade, 7CrMoVTiB10-10: N+T (normalized and tempered) versus Q+T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. 7CrMoVTiB10-10 Q+T is the stronger of the two: yield strength 570 MPa (82.7 ksi) against 520 MPa (75.4 ksi) for 7CrMoVTiB10-10 N+T, about 10% more; tensile strength follows at 700 MPa (102 ksi) vs 640 MPa (92.8 ksi). In exchange, 7CrMoVTiB10-10 N+T is the more ductile: elongation 23% versus 20% for 7CrMoVTiB10-10 Q+T, and 7CrMoVTiB10-10 Q+T is harder (225 HB vs 205 HB).
7CrMoVTiB10-10 N+TChoose it when the part is bent, formed or impact-loaded.
7CrMoVTiB10-10 Q+TChoose it when strength drives the design.
7CrMoVTiB10-10 N+T vs 7CrMoVTiB10-10 Q+T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
7CrMoVTiB10-10 N+T7CrMoVTiB10-10 Q+T
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 213 GPa30.9 Msi · Shear Modulus 82 GPa11.9 Msi · Bulk Modulus 166 GPa24.1 Msi · Poisson's Ratio 0.3 · Shear Strength 400 MPa58 ksi · Fracture Toughness (K_IC) 130 MPa·√m118 ksi·√in · Hardness, Rockwell B 94 HRB
Physical
Density and transition temperatures.
Same in both: Density 7.84 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,450°C2,642 °F · Liquidus Temperature 1,510°C2,750 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 36 W/m·K20.8 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 560°C1,040 °F · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 22 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability Rating (AISI 1212 = 100 %)
Same in both: Machinability 45 / 100 · Weldability 55 / 100 · Formability (cold) 50 / 100 · Brazeability / Solderability 45 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 32 MJ/kg13,758 BTU/lb · Embodied Carbon (primary production) 2.4 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
7CrMoVTiB10-10 N+T vs 7CrMoVTiB10-10 Q+T — frequently asked
Is 7CrMoVTiB10-10 Q+T stronger than 7CrMoVTiB10-10 N+T?
Yes. 7CrMoVTiB10-10 Q+T has a typical yield strength of 570 MPa (82.7 ksi) against 520 MPa (75.4 ksi) for 7CrMoVTiB10-10 N+T — about 10% more. Tensile strength is 700 MPa (102 ksi) vs 640 MPa (92.8 ksi).
Which condition does FabDigit quote by default, N+T or Q+T?
N+T is the default 7CrMoVTiB10-10 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose 7CrMoVTiB10-10 N+T over 7CrMoVTiB10-10 Q+T?
Pick 7CrMoVTiB10-10 N+T when the part is bent, formed or impact-loaded. Pick 7CrMoVTiB10-10 Q+T when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 7CrMoVTiB10-10 N+T and 7CrMoVTiB10-10 Q+T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.