Steel 708M40-A vs 708M40-CD
Steel · 708M40 temper comparison
708M40-A and 708M40-CD are two conditions of the same steel grade, 708M40: A (solution annealed) versus CD (cold drawn). The chemistry is identical, so every difference below comes from the condition. 708M40-CD is the stronger of the two: yield strength 620 MPa (89.9 ksi) against 420 MPa (60.9 ksi) for 708M40-A, about 48% more; tensile strength follows at 760 MPa (110 ksi) vs 655 MPa (95 ksi). In exchange, 708M40-A is the more ductile: elongation 25% versus 14% for 708M40-CD, and 708M40-CD is harder (225 HB vs 190 HB). 708M40-A runs hotter in service (400°C vs 350°C continuous).
708M40-AChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
708M40-CDChoose it when strength drives the design.
708M40-A vs 708M40-CD: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,416°C2,581 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 473 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.65 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 29 MJ/kg12,468 BTU/lb · Embodied Carbon (primary production) 2 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
708M40-A vs 708M40-CD — frequently asked
Is 708M40-CD stronger than 708M40-A?
Yes. 708M40-CD has a typical yield strength of 620 MPa (89.9 ksi) against 420 MPa (60.9 ksi) for 708M40-A — about 48% more. Tensile strength is 760 MPa (110 ksi) vs 655 MPa (95 ksi).
Which condition does FabDigit quote by default, A or CD?
T is the default 708M40 condition in the FabDigit quote flow (neither A nor CD). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, 708M40-A or 708M40-CD?
708M40-A. Its weldability rates fair (45/100) against fair (38/100) for 708M40-CD.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 708M40-A and 708M40-CD side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.