Steel 6150-CR vs 6150 Q&T
Steel · 6150 temper comparison
6150-CR and 6150 Q&T are two conditions of the same steel grade, 6150: CR (cold rolled) versus Q&T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. 6150 Q&T is the stronger of the two: yield strength 1,100 MPa (160 ksi) against 560 MPa (81.2 ksi) for 6150-CR, about 96% more; tensile strength follows at 1,300 MPa (189 ksi) vs 780 MPa (113 ksi). In exchange, 6150-CR is the more ductile: elongation 12% versus 10% for 6150 Q&T, and 6150 Q&T is harder (375 HB vs 230 HB). On the shop floor, 6150-CR machines more easily (fair vs poor) and 6150-CR welds better (30 vs 18 out of 100).
6150-CRChoose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
6150 Q&TChoose it when strength drives the design.
6150-CR vs 6150 Q&T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell C
Same in both: Elastic (Young's) Modulus 207 GPa30 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Charpy V-Notch Impact (RT) 35 J25.8 ft·lbf
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,480°C2,696 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 44 W/m·K25.4 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.61 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 30 / 100 · Brazeability / Solderability 45 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 30 MJ/kg12,898 BTU/lb · Embodied Carbon (primary production) 2.2 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 35%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
6150-CR vs 6150 Q&T — frequently asked
Is 6150 Q&T stronger than 6150-CR?
Yes. 6150 Q&T has a typical yield strength of 1,100 MPa (160 ksi) against 560 MPa (81.2 ksi) for 6150-CR — about 96% more. Tensile strength is 1,300 MPa (189 ksi) vs 780 MPa (113 ksi).
Which condition does FabDigit quote by default, CR or Q&T?
HR is the default 6150 condition in the FabDigit quote flow (neither CR nor Q&T). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 6150-CR or 6150 Q&T?
6150-CR. Its machinability rates fair (50/100) against poor (32/100) for 6150 Q&T; for welding the order is 6150-CR first (poor, 30/100) then 6150 Q&T (poor, 18/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 6150-CR and 6150 Q&T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.