Steel 52100 Cold Drawn vs 52100 Normalized
Steel · 52100 temper comparison
52100 Cold Drawn and 52100 Normalized are two conditions of the same steel grade, 52100: Cold Drawn versus Normalized. The chemistry is identical, so every difference below comes from the condition. 52100 Normalized is the stronger of the two: yield strength 700 MPa (102 ksi) against 620 MPa (89.9 ksi) for 52100 Cold Drawn, about 13% more; tensile strength follows at 1,200 MPa (174 ksi) vs 780 MPa (113 ksi). In exchange, 52100 Cold Drawn is the more ductile: elongation 10% versus 8% for 52100 Normalized, and 52100 Normalized is harder (340 HB vs 220 HB). 52100 Normalized runs hotter in service (400°C vs 150°C continuous). On the shop floor, 52100 Cold Drawn machines more easily (fair vs poor).
52100 Cold DrawnChoose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
52100 NormalizedChoose it when strength drives the design, or when the part sees heat.
52100 Cold Drawn vs 52100 Normalized: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
52100 Cold Drawn52100 Normalized
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Bulk Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 80 GPa11.6 Msi
Physical
Density and transition temperatures.
Melting Point (Solidus)
Liquidus Temperature
Same in both: Density 7.81 g/cm³0.28 lb/in³
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Min Service Temperature
Same in both: Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.9 µm/m·K6.6 µin/in·°F · Latent Heat of Fusion 247 J/g106 BTU/lb
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7 % IACS · Electrical Resistivity 2.6×10⁻⁷ Ω·m10.2 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Polishability
Same in both: Castability 25 / 100 · Brazeability / Solderability 35 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Same in both: Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
52100 Cold Drawn vs 52100 Normalized — frequently asked
Is 52100 Normalized stronger than 52100 Cold Drawn?
Yes. 52100 Normalized has a typical yield strength of 700 MPa (102 ksi) against 620 MPa (89.9 ksi) for 52100 Cold Drawn — about 13% more. Tensile strength is 1,200 MPa (174 ksi) vs 780 MPa (113 ksi).
Which condition does FabDigit quote by default, Cold Drawn or Normalized?
Annealed is the default 52100 condition in the FabDigit quote flow (neither Cold Drawn nor Normalized). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 52100 Cold Drawn or 52100 Normalized?
52100 Cold Drawn. Its machinability rates fair (38/100) against poor (20/100) for 52100 Normalized; for welding the order is 52100 Cold Drawn first (poor, 15/100) then 52100 Normalized (not recommended, 10/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 52100 Cold Drawn and 52100 Normalized side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.