Steel 50CrVA-QT vs 50CrVA-QT45
Steel · 50CrVA temper comparison
50CrVA-QT and 50CrVA-QT45 are two conditions of the same steel grade, 50CrVA: QT (quenched and tempered) versus QT45 (Q&T 45–48 HRC). The chemistry is identical, so every difference below comes from the condition. 50CrVA-QT45 is the stronger of the two: yield strength 1,420 MPa (206 ksi) against 1,200 MPa (174 ksi) for 50CrVA-QT, about 18% more; tensile strength follows at 1,570 MPa (228 ksi) vs 1,350 MPa (196 ksi). In exchange, 50CrVA-QT is the more ductile: elongation 12% versus 9% for 50CrVA-QT45, and 50CrVA-QT45 is harder (435 HB vs 400 HB). 50CrVA-QT runs hotter in service (250°C vs 230°C continuous).
50CrVA-QTChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
50CrVA-QT45Choose it when strength drives the design.
50CrVA-QT vs 50CrVA-QT45: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 206 GPa29.9 Msi · Shear Modulus 79 GPa11.5 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Compressive Strength 1,230 MPa178 ksi
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 44 W/m·K25.4 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Same in both: Weldability 22 / 100 · Formability (cold) 12 / 100 · Brazeability / Solderability 45 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 31 MJ/kg13,328 BTU/lb · Embodied Carbon (primary production) 2.2 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
50CrVA-QT vs 50CrVA-QT45 — frequently asked
Is 50CrVA-QT45 stronger than 50CrVA-QT?
Yes. 50CrVA-QT45 has a typical yield strength of 1,420 MPa (206 ksi) against 1,200 MPa (174 ksi) for 50CrVA-QT — about 18% more. Tensile strength is 1,570 MPa (228 ksi) vs 1,350 MPa (196 ksi).
Which condition does FabDigit quote by default, QT or QT45?
QT is the default 50CrVA condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 50CrVA-QT or 50CrVA-QT45?
50CrVA-QT, by a small margin. Both rate poor for machinability — 32/100 against 24/100 for 50CrVA-QT45.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 50CrVA-QT and 50CrVA-QT45 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.