Steel 4J32-CD vs 4J32-Y2
Steel · 4J32 temper comparison
4J32-CD and 4J32-Y2 are two conditions of the same steel grade, 4J32: CD (cold drawn) versus Y2 (half hard, cold rolled/drawn ≈20–30 % reduction). The chemistry is identical, so every difference below comes from the condition. 4J32-Y2 is the stronger of the two: yield strength 560 MPa (81.2 ksi) against 450 MPa (65.3 ksi) for 4J32-CD, about 24% more; tensile strength follows at 700 MPa (102 ksi) vs 620 MPa (89.9 ksi). In exchange, 4J32-CD is the more ductile: elongation 20% versus 12% for 4J32-Y2, and 4J32-Y2 is harder (225 HB vs 190 HB).
4J32-CDChoose it when the part is bent, formed or impact-loaded.
4J32-Y2Choose it when strength drives the design.
4J32-CD vs 4J32-Y2: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 56 GPa8.1 Msi · Bulk Modulus 112 GPa16.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 8.15 g/cm³0.29 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,450°C2,642 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Expansion (CTE, 20–100 °C)
Same in both: Thermal Conductivity 11 W/m·K6.4 BTU/hr·ft·°F · Specific Heat Capacity 515 J/kg·K0.12 BTU/lb·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 150°C302 °F · Min Service Temperature -50°C-58 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.5 V · Corrosion Resistance 28 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 60 / 100 · Castability 40 / 100 · Brazeability / Solderability 70 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 115 MJ/kg49,441 BTU/lb · Embodied Carbon (primary production) 8.5 kg CO₂/kg · Embodied Water 300 L/kg35.9 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
4J32-CD vs 4J32-Y2 — frequently asked
Is 4J32-Y2 stronger than 4J32-CD?
Yes. 4J32-Y2 has a typical yield strength of 560 MPa (81.2 ksi) against 450 MPa (65.3 ksi) for 4J32-CD — about 24% more. Tensile strength is 700 MPa (102 ksi) vs 620 MPa (89.9 ksi).
Which condition does FabDigit quote by default, CD or Y2?
M is the default 4J32 condition in the FabDigit quote flow (neither CD nor Y2). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose 4J32-CD over 4J32-Y2?
Pick 4J32-CD when the part is bent, formed or impact-loaded. Pick 4J32-Y2 when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 4J32-CD and 4J32-Y2 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.