Steel 4340-CD vs 4340-CR
Steel · 4340 temper comparison
4340-CD and 4340-CR are two conditions of the same steel grade, 4340: CD (cold drawn) versus CR (cold rolled). The chemistry is identical, so every difference below comes from the condition. 4340-CD is the stronger of the two: yield strength 830 MPa (120 ksi) against 620 MPa (89.9 ksi) for 4340-CR, about 34% more; tensile strength follows at 965 MPa (140 ksi) vs 800 MPa (116 ksi). In exchange, 4340-CR is the more ductile: elongation 15% versus 12% for 4340-CD, and 4340-CD is harder (285 HB vs 240 HB). 4340-CR runs hotter in service (400°C vs 350°C continuous).
4340-CDChoose it when strength drives the design.
4340-CRChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
4340-CD vs 4340-CR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Hardness, Rockwell B 100 HRB
Physical
Density and transition temperatures.
Melting Point (Solidus)
Liquidus Temperature
Same in both: Density 7.85 g/cm³0.28 lb/in³
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7 % IACS · Electrical Resistivity 2.48×10⁻⁷ Ω·m9.76 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.62 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 45 / 100 · Brazeability / Solderability 55 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 32 MJ/kg13,758 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
4340-CD vs 4340-CR — frequently asked
Is 4340-CD stronger than 4340-CR?
Yes. 4340-CD has a typical yield strength of 830 MPa (120 ksi) against 620 MPa (89.9 ksi) for 4340-CR — about 34% more. Tensile strength is 965 MPa (140 ksi) vs 800 MPa (116 ksi).
Which condition does FabDigit quote by default, CD or CR?
HR is the default 4340 condition in the FabDigit quote flow (neither CD nor CR). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 4340-CD or 4340-CR?
4340-CR, by a small margin. Both rate fair for machinability — 50/100 against 45/100 for 4340-CD; for welding the order is 4340-CR first (fair, 38/100) then 4340-CD (poor, 30/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 4340-CD and 4340-CR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.