Steel 4320 Annealed vs 4320-CR
Steel · 4320 temper comparison
4320 Annealed and 4320-CR are two conditions of the same steel grade, 4320: Annealed versus CR (cold rolled). The chemistry is identical, so every difference below comes from the condition. 4320-CR is the stronger of the two: yield strength 550 MPa (79.8 ksi) against 425 MPa (61.6 ksi) for 4320 Annealed, about 29% more; tensile strength follows at 700 MPa (102 ksi) vs 580 MPa (84.1 ksi). In exchange, 4320 Annealed is the more ductile: elongation 29% versus 12% for 4320-CR, and 4320-CR is harder (207 HB vs 163 HB). 4320 Annealed runs hotter in service (350°C vs 300°C continuous).
4320 AnnealedChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
4320-CRChoose it when strength drives the design.
4320 Annealed vs 4320-CR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 44 W/m·K25.4 BTU/hr·ft·°F · Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.7 µm/m·K6.5 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -60°C-76 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 11 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Same in both: Machinability Rating (AISI 1212 = 100 %) 60% · Brazeability / Solderability 55 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 31 MJ/kg13,328 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 50 L/kg6 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
4320 Annealed vs 4320-CR — frequently asked
Is 4320-CR stronger than 4320 Annealed?
Yes. 4320-CR has a typical yield strength of 550 MPa (79.8 ksi) against 425 MPa (61.6 ksi) for 4320 Annealed — about 29% more. Tensile strength is 700 MPa (102 ksi) vs 580 MPa (84.1 ksi).
Which condition does FabDigit quote by default, Annealed or CR?
HR is the default 4320 condition in the FabDigit quote flow (neither Annealed nor CR). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 4320 Annealed or 4320-CR?
4320 Annealed. Its machinability rates good (58/100) against fair (52/100) for 4320-CR; for welding the order is 4320 Annealed first (fair, 45/100) then 4320-CR (fair, 38/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 4320 Annealed and 4320-CR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.