Steel 35CrMo Annealed vs 35CrMo-CR
Steel · 35CrMo temper comparison
35CrMo Annealed and 35CrMo-CR are two conditions of the same steel grade, 35CrMo: Annealed versus CR (cold rolled). The chemistry is identical, so every difference below comes from the condition. 35CrMo-CR is the stronger of the two: yield strength 660 MPa (95.7 ksi) against 420 MPa (60.9 ksi) for 35CrMo Annealed, about 57% more; tensile strength follows at 830 MPa (120 ksi) vs 680 MPa (98.6 ksi). In exchange, 35CrMo Annealed is the more ductile: elongation 24% versus 11% for 35CrMo-CR, and 35CrMo-CR is harder (245 HB vs 197 HB). 35CrMo Annealed runs hotter in service (480°C vs 300°C continuous).
35CrMo AnnealedChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
35CrMo-CRChoose it when strength drives the design.
35CrMo Annealed vs 35CrMo-CR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 44 W/m·K25.4 BTU/hr·ft·°F · Specific Heat Capacity 473 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 250 J/g107 BTU/lb · Min Service Temperature -30°C-22 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.61 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Polishability
Same in both: Brazeability / Solderability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 34 MJ/kg14,617 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 30%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
35CrMo Annealed vs 35CrMo-CR — frequently asked
Is 35CrMo-CR stronger than 35CrMo Annealed?
Yes. 35CrMo-CR has a typical yield strength of 660 MPa (95.7 ksi) against 420 MPa (60.9 ksi) for 35CrMo Annealed — about 57% more. Tensile strength is 830 MPa (120 ksi) vs 680 MPa (98.6 ksi).
Which condition does FabDigit quote by default, Annealed or CR?
HR is the default 35CrMo condition in the FabDigit quote flow (neither Annealed nor CR). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 35CrMo Annealed or 35CrMo-CR?
35CrMo Annealed, by a small margin. Both rate good for machinability — 62/100 against 56/100 for 35CrMo-CR; for welding the order is 35CrMo Annealed first (fair, 45/100) then 35CrMo-CR (fair, 38/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 35CrMo Annealed and 35CrMo-CR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.