Steel 3310 Cold Drawn vs 3310 Normalized
Steel · 3310 temper comparison
3310 Cold Drawn and 3310 Normalized are two conditions of the same steel grade, 3310: Cold Drawn versus Normalized. The chemistry is identical, so every difference below comes from the condition. 3310 Cold Drawn is the stronger of the two: yield strength 650 MPa (94.3 ksi) against 560 MPa (81.2 ksi) for 3310 Normalized, about 16% more. In exchange, 3310 Normalized is the more ductile: elongation 20% versus 14% for 3310 Cold Drawn, and 3310 Normalized is harder (250 HB vs 225 HB). On the shop floor, 3310 Cold Drawn machines more easily (fair vs poor).
3310 Cold DrawnChoose it when strength drives the design, or when the part is machined in volume.
3310 NormalizedChoose it when the part is bent, formed or impact-loaded.
3310 Cold Drawn vs 3310 Normalized: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
3310 Cold Drawn3310 Normalized
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 205 GPa29.7 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.5 µm/m·K6.4 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 200°C392 °F · Min Service Temperature -70°C-94 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 15 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Same in both: Weldability 22 / 100 · Formability (cold) 30 / 100 · Brazeability / Solderability 55 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 36 MJ/kg15,477 BTU/lb · Embodied Carbon (primary production) 2.6 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
3310 Cold Drawn vs 3310 Normalized — frequently asked
Is 3310 Cold Drawn stronger than 3310 Normalized?
Yes. 3310 Cold Drawn has a typical yield strength of 650 MPa (94.3 ksi) against 560 MPa (81.2 ksi) for 3310 Normalized — about 16% more. Tensile strength is 760 MPa (110 ksi) vs 830 MPa (120 ksi).
Which condition does FabDigit quote by default, Cold Drawn or Normalized?
Annealed is the default 3310 condition in the FabDigit quote flow (neither Cold Drawn nor Normalized). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 3310 Cold Drawn or 3310 Normalized?
3310 Cold Drawn. Its machinability rates fair (45/100) against poor (32/100) for 3310 Normalized.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 3310 Cold Drawn and 3310 Normalized side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.