Steel 20CrNiMo-CD vs 20CrNiMo QT-200
Steel · 20CrNiMo temper comparison
20CrNiMo-CD and 20CrNiMo QT-200 are two conditions of the same steel grade, 20CrNiMo: CD (cold drawn) versus QT-200 (Q&T 200 °C). The chemistry is identical, so every difference below comes from the condition. 20CrNiMo QT-200 is the stronger of the two: yield strength 880 MPa (128 ksi) against 640 MPa (92.8 ksi) for 20CrNiMo-CD, about 38% more; tensile strength follows at 1,080 MPa (157 ksi) vs 780 MPa (113 ksi). 20CrNiMo QT-200 is harder — 340 HB against 220 HB for 20CrNiMo-CD — which matters for wear surfaces and threads. 20CrNiMo-CD runs hotter in service (350°C vs 180°C continuous). On the shop floor, 20CrNiMo-CD machines more easily (good vs fair) and 20CrNiMo QT-200 forms better (good vs fair).
20CrNiMo-CDChoose it when the part sees heat, or when the part is machined in volume.
20CrNiMo QT-200Choose it when strength drives the design, or when surface hardness matters.
20CrNiMo-CD vs 20CrNiMo QT-200: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Elongation at Break 12%
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,425°C2,597 °F · Liquidus Temperature 1,510°C2,750 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 475 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.8 µm/m·K6.6 µin/in·°F · Latent Heat of Fusion 247 J/g106 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 8 % IACS · Electrical Resistivity 2.2×10⁻⁷ Ω·m8.66 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.61 V · Corrosion Resistance 12 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 65 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 33 MJ/kg14,187 BTU/lb · Embodied Carbon (primary production) 2.2 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
20CrNiMo-CD vs 20CrNiMo QT-200 — frequently asked
Is 20CrNiMo QT-200 stronger than 20CrNiMo-CD?
Yes. 20CrNiMo QT-200 has a typical yield strength of 880 MPa (128 ksi) against 640 MPa (92.8 ksi) for 20CrNiMo-CD — about 38% more. Tensile strength is 1,080 MPa (157 ksi) vs 780 MPa (113 ksi).
Which condition does FabDigit quote by default, CD or QT-200?
A is the default 20CrNiMo condition in the FabDigit quote flow (neither CD nor QT-200). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 20CrNiMo-CD or 20CrNiMo QT-200?
20CrNiMo-CD. Its machinability rates good (62/100) against fair (38/100) for 20CrNiMo QT-200; for welding the order is 20CrNiMo QT-200 first (good, 55/100) then 20CrNiMo-CD (fair, 50/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 20CrNiMo-CD and 20CrNiMo QT-200 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.