Steel 15CDV6-CR vs 15CDV6-HR
Steel · 15CDV6 temper comparison
15CDV6-CR and 15CDV6-HR are two conditions of the same steel grade, 15CDV6: CR (cold rolled) versus HR (hot rolled). The chemistry is identical, so every difference below comes from the condition. 15CDV6-CR is the stronger of the two: yield strength 800 MPa (116 ksi) against 650 MPa (94.3 ksi) for 15CDV6-HR, about 23% more; tensile strength follows at 950 MPa (138 ksi) vs 900 MPa (131 ksi). In exchange, 15CDV6-HR is the more ductile: elongation 15% versus 9% for 15CDV6-CR, and 15CDV6-CR is harder (290 HB vs 260 HB). 15CDV6-HR runs hotter in service (450°C vs 400°C continuous).
15CDV6-CRChoose it when strength drives the design.
15CDV6-HRChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
15CDV6-CR vs 15CDV6-HR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 207 GPa30 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,490°C2,714 °F · Liquidus Temperature 1,520°C2,768 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 42 W/m·K24.3 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.3 µm/m·K6.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -60°C-76 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 7.5 % IACS · Electrical Resistivity 2.3×10⁻⁷ Ω·m9.06 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 15 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 55 / 100 · Polishability 65 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 33 MJ/kg14,187 BTU/lb · Embodied Carbon (primary production) 2.4 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 20%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
15CDV6-CR vs 15CDV6-HR — frequently asked
Is 15CDV6-CR stronger than 15CDV6-HR?
Yes. 15CDV6-CR has a typical yield strength of 800 MPa (116 ksi) against 650 MPa (94.3 ksi) for 15CDV6-HR — about 23% more. Tensile strength is 950 MPa (138 ksi) vs 900 MPa (131 ksi).
Which condition does FabDigit quote by default, CR or HR?
HR is the default 15CDV6 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose 15CDV6-CR over 15CDV6-HR?
Pick 15CDV6-CR when strength drives the design. Pick 15CDV6-HR when the part is bent, formed or impact-loaded, or when the part sees heat.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 15CDV6-CR and 15CDV6-HR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.