Steel 10CrMo9-10 +A vs 10CrMo9-10 +QT
Steel · 10CrMo9-10 temper comparison
10CrMo9-10 +A and 10CrMo9-10 +QT are two conditions of the same steel grade, 10CrMo9-10: +A (annealed) versus +QT (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. 10CrMo9-10 +QT is the stronger of the two: yield strength 460 MPa (66.7 ksi) against 280 MPa (40.6 ksi) for 10CrMo9-10 +A, about 64% more; tensile strength follows at 650 MPa (94.3 ksi) vs 470 MPa (68.2 ksi). In exchange, 10CrMo9-10 +A is the more ductile: elongation 28% versus 20% for 10CrMo9-10 +QT, and 10CrMo9-10 +QT is harder (205 HB vs 145 HB). On the shop floor, 10CrMo9-10 +A machines more easily (good vs fair).
10CrMo9-10 +AChoose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
10CrMo9-10 +QTChoose it when strength drives the design.
10CrMo9-10 +A vs 10CrMo9-10 +QT: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Compressive Strength 360 MPa52.2 ksi · Charpy V-Notch Impact (RT) 110 J81.1 ft·lbf
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,450°C2,642 °F · Liquidus Temperature 1,510°C2,750 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 37 W/m·K21.4 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12 µm/m·K6.7 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 550°C1,022 °F · Min Service Temperature -30°C-22 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 8 % IACS · Electrical Resistivity 2.1×10⁻⁷ Ω·m8.27 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V · Corrosion Resistance 15 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 45 / 100 · Polishability 50 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 31 MJ/kg13,328 BTU/lb · Embodied Carbon (primary production) 2.3 kg CO₂/kg · Embodied Water 55 L/kg6.6 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
10CrMo9-10 +A vs 10CrMo9-10 +QT — frequently asked
Is 10CrMo9-10 +QT stronger than 10CrMo9-10 +A?
Yes. 10CrMo9-10 +QT has a typical yield strength of 460 MPa (66.7 ksi) against 280 MPa (40.6 ksi) for 10CrMo9-10 +A — about 64% more. Tensile strength is 650 MPa (94.3 ksi) vs 470 MPa (68.2 ksi).
Which condition does FabDigit quote by default, +A or +QT?
+NT is the default 10CrMo9-10 condition in the FabDigit quote flow (neither +A nor +QT). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 10CrMo9-10 +A or 10CrMo9-10 +QT?
10CrMo9-10 +A. Its machinability rates good (62/100) against fair (45/100) for 10CrMo9-10 +QT; for welding the order is 10CrMo9-10 +A first (good, 60/100) then 10CrMo9-10 +QT (good, 55/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 10CrMo9-10 +A and 10CrMo9-10 +QT side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.