Steel 1.2343 Annealed vs 1.2343 Nitrided
Steel · 1.2343 temper comparison
1.2343 Annealed and 1.2343 Nitrided are two conditions of the same steel grade, 1.2343: Annealed versus Nitrided. The chemistry is identical, so every difference below comes from the condition. 1.2343 Nitrided is the stronger of the two: yield strength 1,300 MPa (189 ksi) against 500 MPa (72.5 ksi) for 1.2343 Annealed, about 160% more; tensile strength follows at 1,500 MPa (218 ksi) vs 800 MPa (116 ksi). In exchange, 1.2343 Annealed is the more ductile: elongation 16% versus 8% for 1.2343 Nitrided, and 1.2343 Nitrided is harder (425 HB vs 205 HB). 1.2343 Nitrided runs hotter in service (500°C vs 400°C continuous). On the shop floor, 1.2343 Annealed machines more easily (fair vs not recommended) and 1.2343 Annealed welds better (fair vs not recommended).
1.2343 AnnealedChoose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
1.2343 NitridedChoose it when strength drives the design, or when the part sees heat.
1.2343 Annealed vs 1.2343 Nitrided: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
1.2343 Annealed1.2343 Nitrided
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 81 GPa11.7 Msi · Bulk Modulus 170 GPa24.7 Msi · Poisson's Ratio 0.3 · Hardness, Rockwell B 94 HRB
Physical
Density and transition temperatures.
Same in both: Density 7.8 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,470°C2,678 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 11.9 µm/m·K6.6 µin/in·°F · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 3.3 % IACS · Electrical Resistivity 5.2×10⁻⁷ Ω·m20.5 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.6 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 30 / 100 · Brazeability / Solderability 40 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 34 MJ/kg14,617 BTU/lb · Embodied Carbon (primary production) 2.5 kg CO₂/kg · Embodied Water 60 L/kg7.2 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1.2343 Annealed vs 1.2343 Nitrided — frequently asked
Is 1.2343 Nitrided stronger than 1.2343 Annealed?
Yes. 1.2343 Nitrided has a typical yield strength of 1,300 MPa (189 ksi) against 500 MPa (72.5 ksi) for 1.2343 Annealed — about 160% more. Tensile strength is 1,500 MPa (218 ksi) vs 800 MPa (116 ksi).
Which condition does FabDigit quote by default, Annealed or Nitrided?
Annealed is the default 1.2343 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 1.2343 Annealed or 1.2343 Nitrided?
1.2343 Annealed. Its machinability rates fair (45/100) against not recommended (5/100) for 1.2343 Nitrided; for welding the order is 1.2343 Annealed first (fair, 45/100) then 1.2343 Nitrided (not recommended, 5/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1.2343 Annealed and 1.2343 Nitrided side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.