Stainless Steel S46910 1/2H+A vs S46910-A
Stainless Steel · S46910 temper comparison
S46910 1/2H+A and S46910-A are two conditions of the same stainless steel grade, S46910: 1/2H+A (1/2H + Aged) versus A (solution annealed). The chemistry is identical, so every difference below comes from the condition. S46910 1/2H+A is the stronger of the two: yield strength 1,860 MPa (270 ksi) against 830 MPa (120 ksi) for S46910-A, about 124% more; tensile strength follows at 1,930 MPa (280 ksi) vs 1,030 MPa (149 ksi). In exchange, S46910-A is the more ductile: elongation 16% versus 8% for S46910 1/2H+A, and S46910 1/2H+A is harder (53 HRC vs 33 HRC). On the shop floor, S46910-A machines more easily (fair vs poor) and S46910-A welds better (good vs fair).
S46910 1/2H+AChoose it when strength drives the design.
S46910-AChoose it when the part is bent, formed or impact-loaded, or when the part is machined in volume.
S46910 1/2H+A vs S46910-A: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.85 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,400°C2,552 °F · Liquidus Temperature 1,440°C2,624 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 16 W/m·K9.2 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.5 µm/m·K5.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 400°C752 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.2 % IACS · Electrical Resistivity 8×10⁻⁷ Ω·m31.5 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.28 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 40 / 100 · Polishability 80 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 70 MJ/kg30,095 BTU/lb · Embodied Carbon (primary production) 5.5 kg CO₂/kg · Embodied Water 130 L/kg15.6 gal/lb · Typical Recycled Content 25%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
S46910 1/2H+A vs S46910-A — frequently asked
Is S46910 1/2H+A stronger than S46910-A?
Yes. S46910 1/2H+A has a typical yield strength of 1,860 MPa (270 ksi) against 830 MPa (120 ksi) for S46910-A — about 124% more. Tensile strength is 1,930 MPa (280 ksi) vs 1,030 MPa (149 ksi).
Which condition does FabDigit quote by default, 1/2H+A or A?
FH+A is the default S46910 condition in the FabDigit quote flow (neither 1/2H+A nor A). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, S46910 1/2H+A or S46910-A?
S46910-A. Its machinability rates fair (38/100) against poor (24/100) for S46910 1/2H+A; for welding the order is S46910-A first (good, 65/100) then S46910 1/2H+A (fair, 50/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in S46910 1/2H+A and S46910-A side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.