Stainless Steel S41425-A vs S41425-T
Stainless Steel · S41425 temper comparison
S41425-A and S41425-T are two conditions of the same stainless steel grade, S41425: A (solution annealed) versus T (quenched and tempered). The chemistry is identical, so every difference below comes from the condition. S41425-T is the stronger of the two: yield strength 690 MPa (100 ksi) against 570 MPa (82.7 ksi) for S41425-A, about 21% more; tensile strength follows at 850 MPa (123 ksi) vs 760 MPa (110 ksi). In exchange, S41425-A is the more ductile: elongation 24% versus 19% for S41425-T, and S41425-T is harder (255 HB vs 235 HB).
S41425-AChoose it when the part is bent, formed or impact-loaded.
S41425-TChoose it when strength drives the design.
S41425-A vs S41425-T: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29
Physical
Density and transition temperatures.
Same in both: Density 7.75 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,400°C2,552 °F · Liquidus Temperature 1,490°C2,714 °F
Thermal
How each material carries heat and how hot it can run.
Min Service Temperature
Same in both: Thermal Conductivity 25 W/m·K14.4 BTU/hr·ft·°F · Specific Heat Capacity 470 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.8 µm/m·K6 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 480°C896 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.5 % IACS · Electrical Resistivity 7×10⁻⁷ Ω·m27.6 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.28 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Polishability
Same in both: Brazeability / Solderability 40 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 53 MJ/kg22,786 BTU/lb · Embodied Carbon (primary production) 3.4 kg CO₂/kg · Embodied Water 130 L/kg15.6 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
S41425-A vs S41425-T — frequently asked
Is S41425-T stronger than S41425-A?
Yes. S41425-T has a typical yield strength of 690 MPa (100 ksi) against 570 MPa (82.7 ksi) for S41425-A — about 21% more. Tensile strength is 850 MPa (123 ksi) vs 760 MPa (110 ksi).
Which condition does FabDigit quote by default, A or T?
HT is the default S41425 condition in the FabDigit quote flow (neither A nor T). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, S41425-A or S41425-T?
S41425-A, by a small margin. Both rate fair for machinability — 47/100 against 42/100 for S41425-T; for welding the order is S41425-T first (very good, 70/100) then S41425-A (good, 65/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in S41425-A and S41425-T side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.