Stainless Steel S32707-AW vs S32707-CD
Stainless Steel · S32707 temper comparison
S32707-AW and S32707-CD are two conditions of the same stainless steel grade, S32707: AW (as-welded deposit) versus CD (cold drawn). The chemistry is identical, so every difference below comes from the condition. S32707-CD is the stronger of the two: yield strength 950 MPa (138 ksi) against 720 MPa (104 ksi) for S32707-AW, about 32% more; tensile strength follows at 1,100 MPa (160 ksi) vs 930 MPa (135 ksi). In exchange, S32707-AW is the more ductile: elongation 22% versus 18% for S32707-CD, and S32707-CD is harder (340 HB vs 290 HB). S32707-CD runs hotter in service (280°C vs 250°C continuous).
S32707-AWChoose it when the part is bent, formed or impact-loaded.
S32707-CDChoose it when strength drives the design, or when the part sees heat.
S32707-AW vs S32707-CD: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3 · Reduction in Area 45%
Physical
Density and transition temperatures.
Same in both: Density 7.8 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,345°C2,453 °F · Liquidus Temperature 1,420°C2,588 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 13 W/m·K7.5 BTU/hr·ft·°F · Specific Heat Capacity 480 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.5 µm/m·K6.9 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -50°C-58 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 1.7 % IACS · Electrical Resistivity 1×10⁻⁶ Ω·m39.4 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.05 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Weldability
Formability (cold)
Same in both: Machinability 20 / 100 · Machinability Rating (AISI 1212 = 100 %) 13% · Castability 35 / 100 · Brazeability / Solderability 30 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 62 MJ/kg26,655 BTU/lb · Embodied Carbon (primary production) 6 kg CO₂/kg · Embodied Water 220 L/kg26.4 gal/lb · Typical Recycled Content 60%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
S32707-AW vs S32707-CD — frequently asked
Is S32707-CD stronger than S32707-AW?
Yes. S32707-CD has a typical yield strength of 950 MPa (138 ksi) against 720 MPa (104 ksi) for S32707-AW — about 32% more. Tensile strength is 1,100 MPa (160 ksi) vs 930 MPa (135 ksi).
Which condition does FabDigit quote by default, AW or CD?
SA is the default S32707 condition in the FabDigit quote flow (neither AW nor CD). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, S32707-AW or S32707-CD?
S32707-AW. Its weldability rates good (55/100) against fair (48/100) for S32707-CD.
Ready to make it?
Upload a CAD file and FabDigit prices the part in S32707-AW and S32707-CD side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.