Stainless Steel CC50 Annealed vs CC50 Ni2-4N
Stainless Steel · CC50 temper comparison
CC50 Annealed and CC50 Ni2-4N are two conditions of the same stainless steel grade, CC50: Annealed versus Ni2-4N (CC50 with 2.0–4.0 % Ni and ≤0.15 % N). The chemistry is identical, so every difference below comes from the condition. CC50 Ni2-4N is the stronger of the two: yield strength 290 MPa (42.1 ksi) against 275 MPa (39.9 ksi) for CC50 Annealed, about 5% more; tensile strength follows at 510 MPa (74 ksi) vs 480 MPa (69.6 ksi). CC50 Ni2-4N is the more ductile: elongation 14% versus 10% for CC50 Annealed.
CC50 Ni2-4NChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
CC50 Annealed vs CC50 Ni2-4N: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.28
Physical
Density and transition temperatures.
Same in both: Density 7.6 g/cm³0.27 lb/in³ · Melting Point (Solidus) 1,370°C2,498 °F · Liquidus Temperature 1,450°C2,642 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Same in both: Specific Heat Capacity 500 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.5 µm/m·K5.8 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 1,090°C1,994 °F · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.25 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 65 / 100 · Brazeability / Solderability 45 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 55 MJ/kg23,646 BTU/lb · Embodied Carbon (primary production) 4.2 kg CO₂/kg · Embodied Water 110 L/kg13.2 gal/lb · Typical Recycled Content 65%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
CC50 Annealed vs CC50 Ni2-4N — frequently asked
Is CC50 Ni2-4N stronger than CC50 Annealed?
Yes. CC50 Ni2-4N has a typical yield strength of 290 MPa (42.1 ksi) against 275 MPa (39.9 ksi) for CC50 Annealed — about 5% more. Tensile strength is 510 MPa (74 ksi) vs 480 MPa (69.6 ksi).
Which condition does FabDigit quote by default, Annealed or Ni2-4N?
Annealed is the default CC50 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, CC50 Annealed or CC50 Ni2-4N?
CC50 Ni2-4N. Its weldability rates fair (35/100) against poor (30/100) for CC50 Annealed.
Ready to make it?
Upload a CAD file and FabDigit prices the part in CC50 Annealed and CC50 Ni2-4N side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.