Stainless Steel AUS-10-CR vs AUS-10 QT60-62-CRYO
Stainless Steel · AUS-10 temper comparison
AUS-10-CR and AUS-10 QT60-62-CRYO are two conditions of the same stainless steel grade, AUS-10: CR (cold rolled) versus QT60-62-CRYO (Q&T 60–62 HRC). The chemistry is identical, so every difference below comes from the condition. AUS-10 QT60-62-CRYO is the stronger of the two: yield strength 2,000 MPa (290 ksi) against 780 MPa (113 ksi) for AUS-10-CR, about 156% more; tensile strength follows at 2,150 MPa (312 ksi) vs 950 MPa (138 ksi). In exchange, AUS-10-CR is the more ductile: elongation 6% versus 1.5% for AUS-10 QT60-62-CRYO, and AUS-10-CR is harder (285 HB vs 240 HB). AUS-10-CR runs hotter in service (300°C vs 250°C continuous). On the shop floor, AUS-10-CR machines more easily (poor vs not recommended).
AUS-10-CRChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
AUS-10 QT60-62-CRYOChoose it when strength drives the design.
AUS-10-CR vs AUS-10 QT60-62-CRYO: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 200 GPa29 Msi · Shear Modulus 78 GPa11.3 Msi · Bulk Modulus 165 GPa23.9 Msi · Poisson's Ratio 0.28
Physical
Density and transition temperatures.
Same in both: Density 7.7 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,370°C2,498 °F · Liquidus Temperature 1,480°C2,696 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 24 W/m·K13.9 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10.2 µm/m·K5.7 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -40°C-40 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.9 % IACS · Electrical Resistivity 6×10⁻⁷ Ω·m23.6 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.3 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 30 / 100 · Brazeability / Solderability 45 / 100 · Polishability 80 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 45 MJ/kg19,347 BTU/lb · Embodied Carbon (primary production) 3.3 kg CO₂/kg · Embodied Water 130 L/kg15.6 gal/lb · Typical Recycled Content 50%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
AUS-10-CR vs AUS-10 QT60-62-CRYO — frequently asked
Is AUS-10 QT60-62-CRYO stronger than AUS-10-CR?
Yes. AUS-10 QT60-62-CRYO has a typical yield strength of 2,000 MPa (290 ksi) against 780 MPa (113 ksi) for AUS-10-CR — about 156% more. Tensile strength is 2,150 MPa (312 ksi) vs 950 MPa (138 ksi).
Which condition does FabDigit quote by default, CR or QT60-62-CRYO?
Annealed is the default AUS-10 condition in the FabDigit quote flow (neither CR nor QT60-62-CRYO). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, AUS-10-CR or AUS-10 QT60-62-CRYO?
AUS-10-CR. Its machinability rates poor (30/100) against not recommended (8/100) for AUS-10 QT60-62-CRYO; for welding the order is AUS-10 QT60-62-CRYO first (poor, 25/100) then AUS-10-CR (poor, 20/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in AUS-10-CR and AUS-10 QT60-62-CRYO side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.