Stainless Steel 201LN 3/4H vs 201LN-ANN
Stainless Steel · 201LN temper comparison
201LN 3/4H and 201LN-ANN are two conditions of the same stainless steel grade, 201LN: 3/4H (three-quarter hard) versus ANN (annealed). The chemistry is identical, so every difference below comes from the condition. 201LN 3/4H is the stronger of the two: yield strength 980 MPa (142 ksi) against 380 MPa (55.1 ksi) for 201LN-ANN, about 158% more; tensile strength follows at 1,250 MPa (181 ksi) vs 750 MPa (109 ksi). In exchange, 201LN-ANN is the more ductile: elongation 50% versus 12% for 201LN 3/4H, and 201LN 3/4H is harder (345 HB vs 195 HB). 201LN-ANN runs hotter in service (550°C vs 290°C continuous). On the shop floor, 201LN-ANN welds better (very good vs good).
201LN 3/4HChoose it when strength drives the design.
201LN-ANNChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
201LN 3/4H vs 201LN-ANN: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Vickers
Same in both: Shear Modulus 77 GPa11.2 Msi · Bulk Modulus 150 GPa21.8 Msi · Poisson's Ratio 0.29 · Hardness, Rockwell B 90 HRB
Physical
Density and transition temperatures.
Same in both: Density 7.8 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,400°C2,552 °F · Liquidus Temperature 1,450°C2,642 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 16 W/m·K9.2 BTU/hr·ft·°F · Specific Heat Capacity 500 J/kg·K0.12 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 16.9 µm/m·K9.4 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.12 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Castability 40 / 100 · Brazeability / Solderability 60 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 45 MJ/kg19,347 BTU/lb · Embodied Carbon (primary production) 3.6 kg CO₂/kg · Embodied Water 120 L/kg14.4 gal/lb · Typical Recycled Content 60%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
201LN 3/4H vs 201LN-ANN — frequently asked
Is 201LN 3/4H stronger than 201LN-ANN?
Yes. 201LN 3/4H has a typical yield strength of 980 MPa (142 ksi) against 380 MPa (55.1 ksi) for 201LN-ANN — about 158% more. Tensile strength is 1,250 MPa (181 ksi) vs 750 MPa (109 ksi).
Which condition does FabDigit quote by default, 3/4H or ANN?
ANN is the default 201LN condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 201LN 3/4H or 201LN-ANN?
201LN 3/4H. Its machinability rates fair (40/100) against poor (33/100) for 201LN-ANN; for welding the order is 201LN-ANN first (very good, 80/100) then 201LN 3/4H (good, 60/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 201LN 3/4H and 201LN-ANN side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.