Stainless Steel 1.4565-CD vs 1.4565 CW-HS
Stainless Steel · 1.4565 temper comparison
1.4565-CD and 1.4565 CW-HS are two conditions of the same stainless steel grade, 1.4565: CD (cold drawn) versus CW-HS (cold Worked High Strength). The chemistry is identical, so every difference below comes from the condition. 1.4565 CW-HS is the stronger of the two: yield strength 900 MPa (131 ksi) against 700 MPa (102 ksi) for 1.4565-CD, about 29% more; tensile strength follows at 1,100 MPa (160 ksi) vs 950 MPa (138 ksi). In exchange, 1.4565-CD is the more ductile: elongation 30% versus 20% for 1.4565 CW-HS, and 1.4565 CW-HS is harder (330 HB vs 280 HB).
1.4565-CDChoose it when the part is bent, formed or impact-loaded.
1.4565 CW-HSChoose it when strength drives the design.
1.4565-CD vs 1.4565 CW-HS: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell C
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 190 GPa27.6 Msi · Shear Modulus 73 GPa10.6 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.3 · Hardness, Rockwell B 96 HRB
Physical
Density and transition temperatures.
Same in both: Density 8 g/cm³0.29 lb/in³ · Melting Point (Solidus) 1,350°C2,462 °F · Liquidus Temperature 1,400°C2,552 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 12 W/m·K6.9 BTU/hr·ft·°F · Specific Heat Capacity 480 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 15 µm/m·K8.3 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Max Service Temperature (continuous) 300°C572 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Same in both: Electrical Conductivity 1.9 % IACS
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.05 V · Corrosion Resistance 88 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 50 / 100 · Polishability 75 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 75 MJ/kg32,244 BTU/lb · Embodied Carbon (primary production) 5.5 kg CO₂/kg · Embodied Water 200 L/kg24 gal/lb · Typical Recycled Content 45%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1.4565-CD vs 1.4565 CW-HS — frequently asked
Is 1.4565 CW-HS stronger than 1.4565-CD?
Yes. 1.4565 CW-HS has a typical yield strength of 900 MPa (131 ksi) against 700 MPa (102 ksi) for 1.4565-CD — about 29% more. Tensile strength is 1,100 MPa (160 ksi) vs 950 MPa (138 ksi).
Which condition does FabDigit quote by default, CD or CW-HS?
SA is the default 1.4565 condition in the FabDigit quote flow (neither CD nor CW-HS). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 1.4565-CD or 1.4565 CW-HS?
1.4565-CD, by a small margin. Both rate poor for machinability — 20/100 against 15/100 for 1.4565 CW-HS; for welding the order is 1.4565-CD first (good, 60/100) then 1.4565 CW-HS (good, 55/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1.4565-CD and 1.4565 CW-HS side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.