Stainless Steel 1.4104 +A vs 1.4104-H
Stainless Steel · 1.4104 temper comparison
1.4104 +A and 1.4104-H are two conditions of the same stainless steel grade, 1.4104: +A (annealed) versus H (hardened). The chemistry is identical, so every difference below comes from the condition. 1.4104-H is the stronger of the two: yield strength 950 MPa (138 ksi) against 340 MPa (49.3 ksi) for 1.4104 +A, about 179% more; tensile strength follows at 1,250 MPa (181 ksi) vs 560 MPa (81.2 ksi). In exchange, 1.4104 +A is the more ductile: elongation 20% versus 6% for 1.4104-H, and 1.4104-H is harder (400 HB vs 185 HB). 1.4104 +A runs hotter in service (550°C vs 250°C continuous). On the shop floor, 1.4104 +A machines more easily (very good vs fair).
1.4104 +AChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
1.4104-HChoose it when strength drives the design.
1.4104 +A vs 1.4104-H: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all stainless steel grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 215 GPa31.2 Msi · Shear Modulus 83 GPa12 Msi · Bulk Modulus 160 GPa23.2 Msi · Poisson's Ratio 0.29 · Reduction in Area 45% · Compressive Strength 340 MPa49.3 ksi · Shear Strength 350 MPa50.8 ksi · Fracture Toughness (K_IC) 45 MPa·√m41 ksi·√in · Hardness, Rockwell B 90 HRB
Physical
Density and transition temperatures.
Same in both: Density 7.7 g/cm³0.28 lb/in³ · Melting Point (Solidus) 1,420°C2,588 °F · Liquidus Temperature 1,500°C2,732 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 25 W/m·K14.4 BTU/hr·ft·°F · Specific Heat Capacity 460 J/kg·K0.11 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 10 µm/m·K5.6 µin/in·°F · Latent Heat of Fusion 270 J/g116 BTU/lb · Min Service Temperature -20°C-4 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 2.5 % IACS · Electrical Resistivity 7×10⁻⁷ Ω·m27.6 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.35 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 15 / 100 · Castability 30 / 100 · Brazeability / Solderability 40 / 100 · Polishability 40 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 50 MJ/kg21,496 BTU/lb · Embodied Carbon (primary production) 3.8 kg CO₂/kg · Embodied Water 110 L/kg13.2 gal/lb · Typical Recycled Content 65%
Strength versus weight
Yield strength against density for every stainless steel grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
1.4104 +A vs 1.4104-H — frequently asked
Is 1.4104-H stronger than 1.4104 +A?
Yes. 1.4104-H has a typical yield strength of 950 MPa (138 ksi) against 340 MPa (49.3 ksi) for 1.4104 +A — about 179% more. Tensile strength is 1,250 MPa (181 ksi) vs 560 MPa (81.2 ksi).
Which condition does FabDigit quote by default, +A or H?
+A is the default 1.4104 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 1.4104 +A or 1.4104-H?
1.4104 +A. Its machinability rates very good (78/100) against fair (35/100) for 1.4104-H.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 1.4104 +A and 1.4104-H side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.