PAS CF30 vs PAS GF20
Polymer · PAS grade comparison
PAS CF30 and PAS GF20 are two grades of the same polymer grade, PAS: CF30 (30 % carbon-fibre reinforced) versus GF20 (20 % glass-fibre reinforced). The chemistry is identical, so every difference below comes from the condition. PAS CF30 is the stronger of the two: tensile strength 165 MPa (23.9 ksi) against 115 MPa (16.7 ksi) for PAS GF20, about 43% more. In exchange, PAS GF20 is the more ductile: elongation 3.5% versus 2% for PAS CF30. PAS CF30 is stiffer (17 GPa vs 6.5 GPa) and PAS CF30 conducts heat better (0.6 W/m·K vs 0.22 W/m·K).
PAS CF30Choose it when strength drives the design.
PAS GF20Choose it when the part is bent, formed or impact-loaded.
PAS CF30 vs PAS GF20: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all polymer grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Elongation at Break
Flexural Strength
Flexural Modulus
Izod Impact, Notched
Same in both: Shear Modulus 0.9 GPa0.13 Msi · Poisson's Ratio 0.4 · Yield Strength (0.2% offset) 75 MPa10.9 ksi · Compressive Strength 100 MPa14.5 ksi · Compressive Modulus 2.5 GPa0.36 Msi · Shear Strength 62 MPa9 ksi · Fracture Toughness (K_IC) 2.6 MPa·√m2.4 ksi·√in · Hardness, Shore A 96 Shore A · Hardness, Shore D 85 Shore D · Hardness, Rockwell M 88 HRM · Hardness, Rockwell R 120 HRR
Physical
Density and transition temperatures.
Density
Same in both: Glass Transition (Tg) 210°C410 °F · Water Absorption (24 h) 0.4% · Water Absorption (Saturation) 1.2% · Refractive Index 1.64 · Light Transmission 75%
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Thermal Expansion (CTE, 20–100 °C)
Heat Deflection Temp. @ 1.8 MPa
Same in both: Specific Heat Capacity 1,150 J/kg·K0.27 BTU/lb·°F · Max Service Temperature (continuous) 170°C338 °F · Min Service Temperature -100°C-148 °F · Heat Deflection Temp. @ 0.45 MPa 195°C383 °F · Vicat Softening Point (B50) 210°C410 °F · Limiting Oxygen Index 34% · Max Service Temperature (short-term) 210°C410 °F
Electrical
Conductivity and insulation.
Volume Resistivity
Surface Resistivity
Same in both: Electrical Resistivity 1×10¹⁴ Ω·m3.94×10²¹ µΩ·in · Dielectric Strength 17 kV/mm432 V/mil · Dielectric Constant (1 MHz) 3.4 · Dissipation Factor (1 MHz) 0.008 · Comparative Tracking Index (CTI) 150 V
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Corrosion Resistance 85 / 100 · UV / Weathering Resistance 30 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Mold Shrinkage
Same in both: Weldability 72 / 100 · Formability (cold) 60 / 100 · Polishability 70 / 100 · Melt Flow Rate 20 g/10 min · Processing Melt Temperature (typ.) 360°C680 °F · Mold Temperature (typ.) 150°C302 °F
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 145 MJ/kg62,339 BTU/lb · Embodied Carbon (primary production) 8 kg CO₂/kg · Embodied Water 300 L/kg35.9 gal/lb · Typical Recycled Content 0%
Strength versus weight
Yield strength against density for every polymer grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
PAS CF30 vs PAS GF20 — frequently asked
Is PAS CF30 stronger than PAS GF20?
Yes. PAS CF30 has a typical tensile strength of 165 MPa (23.9 ksi) against 115 MPa (16.7 ksi) for PAS GF20 — about 43% more.
Which grade does FabDigit quote by default, CF30 or GF20?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, PAS CF30 or PAS GF20?
PAS GF20, by a small margin. Both rate fair for machinability — 50/100 against 42/100 for PAS CF30.
Ready to make it?
Upload a CAD file and FabDigit prices the part in PAS CF30 and PAS GF20 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.