Nickel Alloy Alloy 59-CD vs Alloy 59 CR-A
Nickel Alloy · Alloy 59 temper comparison
Alloy 59-CD and Alloy 59 CR-A are two conditions of the same nickel alloy grade, Alloy 59: CD (cold drawn) versus CR-A (cold rolled and bright annealed sheet/strip). The chemistry is identical, so every difference below comes from the condition. Alloy 59-CD is the stronger of the two: yield strength 750 MPa (109 ksi) against 380 MPa (55.1 ksi) for Alloy 59 CR-A, about 97% more; tensile strength follows at 950 MPa (138 ksi) vs 760 MPa (110 ksi). In exchange, Alloy 59 CR-A is the more ductile: elongation 48% versus 22% for Alloy 59-CD, and Alloy 59-CD is harder (290 HB vs 210 HB).
Alloy 59-CDChoose it when strength drives the design.
Alloy 59 CR-AChoose it when the part is bent, formed or impact-loaded.
Alloy 59-CD vs Alloy 59 CR-A: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all nickel alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 210 GPa30.5 Msi · Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 184 GPa26.7 Msi · Poisson's Ratio 0.31
Physical
Density and transition temperatures.
Same in both: Density 8.6 g/cm³0.31 lb/in³ · Melting Point (Solidus) 1,310°C2,390 °F · Liquidus Temperature 1,360°C2,480 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 10.4 W/m·K6 BTU/hr·ft·°F · Specific Heat Capacity 420 J/kg·K0.1 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 12.4 µm/m·K6.9 µin/in·°F · Latent Heat of Fusion 290 J/g125 BTU/lb · Max Service Temperature (continuous) 1,000°C1,832 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 1.3 % IACS · Electrical Resistivity 1.29×10⁻⁶ Ω·m50.8 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.08 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Polishability
Same in both: Machinability Rating (AISI 1212 = 100 %) 12% · Brazeability / Solderability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 180 MJ/kg77,386 BTU/lb · Embodied Carbon (primary production) 14 kg CO₂/kg · Embodied Water 250 L/kg30 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every nickel alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Alloy 59-CD vs Alloy 59 CR-A — frequently asked
Is Alloy 59-CD stronger than Alloy 59 CR-A?
Yes. Alloy 59-CD has a typical yield strength of 750 MPa (109 ksi) against 380 MPa (55.1 ksi) for Alloy 59 CR-A — about 97% more. Tensile strength is 950 MPa (138 ksi) vs 760 MPa (110 ksi).
Which condition does FabDigit quote by default, CD or CR-A?
SA is the default Alloy 59 condition in the FabDigit quote flow (neither CD nor CR-A). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose Alloy 59-CD over Alloy 59 CR-A?
Pick Alloy 59-CD when strength drives the design. Pick Alloy 59 CR-A when the part is bent, formed or impact-loaded.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Alloy 59-CD and Alloy 59 CR-A side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.