Copper Alloy C95300-M01 vs C95300-M07
Copper Alloy · C95300 temper comparison
C95300-M01 and C95300-M07 are two conditions of the same copper alloy grade, C95300: M01 (as sand cast) versus M07 (as continuous cast). The chemistry is identical, so every difference below comes from the condition. C95300-M07 is the stronger of the two: yield strength 195 MPa (28.3 ksi) against 170 MPa (24.7 ksi) for C95300-M01, about 15% more; tensile strength follows at 480 MPa (69.6 ksi) vs 450 MPa (65.3 ksi). In exchange, C95300-M01 is the more ductile: elongation 25% versus 22% for C95300-M07, and C95300-M07 is harder (120 HB vs 110 HB).
C95300-M01Choose it when the part is bent, formed or impact-loaded.
C95300-M07Choose it when strength drives the design.
C95300-M01 vs C95300-M07: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 110 GPa16 Msi · Shear Modulus 41 GPa5.9 Msi · Bulk Modulus 105 GPa15.2 Msi · Poisson's Ratio 0.32 · Compressive Strength 180 MPa26.1 ksi · Shear Strength 330 MPa47.9 ksi
Physical
Density and transition temperatures.
Same in both: Density 7.53 g/cm³0.27 lb/in³ · Melting Point (Solidus) 1,040°C1,904 °F · Liquidus Temperature 1,045°C1,913 °F
Thermal
How each material carries heat and how hot it can run.
Same in both: Thermal Conductivity 58.6 W/m·K33.9 BTU/hr·ft·°F · Specific Heat Capacity 376 J/kg·K0.09 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 16.2 µm/m·K9 µin/in·°F · Latent Heat of Fusion 220 J/g94.6 BTU/lb · Max Service Temperature (continuous) 300°C572 °F · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 13 % IACS · Electrical Resistivity 1.33×10⁻⁷ Ω·m5.24 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.28 V · Corrosion Resistance 72 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Same in both: Machinability 48 / 100 · Machinability Rating (AISI 1212 = 100 %) 55% · Weldability 70 / 100 · Formability (cold) 15 / 100 · Castability 75 / 100 · Brazeability / Solderability 30 / 100 · Polishability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 50 MJ/kg21,496 BTU/lb · Embodied Carbon (primary production) 3.5 kg CO₂/kg · Embodied Water 220 L/kg26.4 gal/lb · Typical Recycled Content 60%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C95300-M01 vs C95300-M07 — frequently asked
Is C95300-M07 stronger than C95300-M01?
Yes. C95300-M07 has a typical yield strength of 195 MPa (28.3 ksi) against 170 MPa (24.7 ksi) for C95300-M01 — about 15% more. Tensile strength is 480 MPa (69.6 ksi) vs 450 MPa (65.3 ksi).
Which condition does FabDigit quote by default, M01 or M07?
M01 is the default C95300 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
When should I choose C95300-M01 over C95300-M07?
Pick C95300-M01 when the part is bent, formed or impact-loaded. Pick C95300-M07 when strength drives the design.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C95300-M01 and C95300-M07 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.