Copper Alloy C52100-H06 vs C52100-O60
Copper Alloy · C52100 temper comparison
C52100-H06 and C52100-O60 are two conditions of the same copper alloy grade, C52100: H06 (extra hard) versus O60 (soft annealed). The chemistry is identical, so every difference below comes from the condition. C52100-H06 is the stronger of the two: yield strength 640 MPa (92.8 ksi) against 150 MPa (21.8 ksi) for C52100-O60, about 4.3 times as much; tensile strength follows at 720 MPa (104 ksi) vs 375 MPa (54.4 ksi). In exchange, C52100-O60 is the more ductile: elongation 62% versus 6% for C52100-H06, and C52100-H06 is harder (198 HB vs 60 HB). C52100-O60 runs hotter in service (220°C vs 175°C continuous).
C52100-H06Choose it when strength drives the design.
C52100-O60Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
C52100-H06 vs C52100-O60: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 41 GPa5.9 Msi · Bulk Modulus 115 GPa16.7 Msi · Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Same in both: Density 8.8 g/cm³0.32 lb/in³ · Melting Point (Solidus) 854°C1,569 °F · Liquidus Temperature 1,000°C1,832 °F
Thermal
How each material carries heat and how hot it can run.
Specific Heat Capacity
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 62 W/m·K35.8 BTU/hr·ft·°F · Thermal Expansion (CTE, 20–100 °C) 18.4 µm/m·K10.2 µin/in·°F · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 13 % IACS · Electrical Resistivity 1.33×10⁻⁷ Ω·m5.24 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.28 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 88 / 100 · Polishability 75 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Same in both: Embodied Water 350 L/kg41.9 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C52100-H06 vs C52100-O60 — frequently asked
Is C52100-H06 stronger than C52100-O60?
Yes. C52100-H06 has a typical yield strength of 640 MPa (92.8 ksi) against 150 MPa (21.8 ksi) for C52100-O60 — about 4.3 times as much. Tensile strength is 720 MPa (104 ksi) vs 375 MPa (54.4 ksi).
Which condition does FabDigit quote by default, H06 or O60?
H04 is the default C52100 condition in the FabDigit quote flow (neither H06 nor O60). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, C52100-H06 or C52100-O60?
C52100-O60. Its weldability rates fair (40/100) against fair (35/100) for C52100-H06.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C52100-H06 and C52100-O60 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.