Copper Alloy C50100-H01 vs C50100-H80
Copper Alloy · C50100 temper comparison
C50100-H01 and C50100-H80 are two conditions of the same copper alloy grade, C50100: H01 (quarter hard) versus H80 (hard drawn). The chemistry is identical, so every difference below comes from the condition. C50100-H80 is the stronger of the two: yield strength 410 MPa (59.5 ksi) against 240 MPa (34.8 ksi) for C50100-H01, about 71% more; tensile strength follows at 450 MPa (65.3 ksi) vs 300 MPa (43.5 ksi). In exchange, C50100-H01 is the more ductile: elongation 25% versus 5% for C50100-H80, and C50100-H80 is harder (135 HB vs 85 HB). C50100-H01 runs hotter in service (200°C vs 175°C continuous).
C50100-H01Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
C50100-H80Choose it when strength drives the design.
C50100-H01 vs C50100-H80: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Rockwell B
Same in both: Elastic (Young's) Modulus 117 GPa17 Msi · Shear Modulus 44 GPa6.4 Msi · Bulk Modulus 130 GPa18.9 Msi · Poisson's Ratio 0.34
Physical
Density and transition temperatures.
Same in both: Density 8.89 g/cm³0.32 lb/in³ · Melting Point (Solidus) 1,050°C1,922 °F · Liquidus Temperature 1,075°C1,967 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 377 J/kg·K0.09 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 17.8 µm/m·K9.9 µin/in·°F · Latent Heat of Fusion 205 J/g88.1 BTU/lb · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.26 V · Corrosion Resistance 66 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Same in both: Machinability Rating (AISI 1212 = 100 %) 20% · Brazeability / Solderability 95 / 100 · Polishability 80 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 57 MJ/kg24,506 BTU/lb · Embodied Carbon (primary production) 3.6 kg CO₂/kg · Embodied Water 300 L/kg35.9 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C50100-H01 vs C50100-H80 — frequently asked
Is C50100-H80 stronger than C50100-H01?
Yes. C50100-H80 has a typical yield strength of 410 MPa (59.5 ksi) against 240 MPa (34.8 ksi) for C50100-H01 — about 71% more. Tensile strength is 450 MPa (65.3 ksi) vs 300 MPa (43.5 ksi).
Which condition does FabDigit quote by default, H01 or H80?
H04 is the default C50100 condition in the FabDigit quote flow (neither H01 nor H80). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, C50100-H01 or C50100-H80?
C50100-H01. Its weldability rates good (60/100) against good (55/100) for C50100-H80.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C50100-H01 and C50100-H80 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.