Copper Alloy C41500-H02 vs C41500-H08
Copper Alloy · C41500 temper comparison
C41500-H02 and C41500-H08 are two conditions of the same copper alloy grade, C41500: H02 (half hard) versus H08 (spring hard). The chemistry is identical, so every difference below comes from the condition. C41500-H08 is the stronger of the two: yield strength 586 MPa (85 ksi) against 400 MPa (58 ksi) for C41500-H02, about 47% more; tensile strength follows at 627 MPa (90.9 ksi) vs 455 MPa (66 ksi). In exchange, C41500-H02 is the more ductile: elongation 12% versus 2% for C41500-H08, and C41500-H08 is harder (195 HV vs 135 HV). C41500-H02 runs hotter in service (150°C vs 130°C continuous).
C41500-H02Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
C41500-H08Choose it when strength drives the design.
C41500-H02 vs C41500-H08: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Rockwell B
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 110 GPa16 Msi · Shear Modulus 41 GPa5.9 Msi · Bulk Modulus 115 GPa16.7 Msi · Poisson's Ratio 0.34 · Hardness, Brinell 128 HB
Physical
Density and transition temperatures.
Same in both: Density 8.78 g/cm³0.32 lb/in³ · Melting Point (Solidus) 955°C1,751 °F · Liquidus Temperature 1,020°C1,868 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 116 W/m·K67 BTU/hr·ft·°F · Specific Heat Capacity 377 J/kg·K0.09 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 18.4 µm/m·K10.2 µin/in·°F · Latent Heat of Fusion 200 J/g86 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 28 % IACS · Electrical Resistivity 6.2×10⁻⁸ Ω·m2.44 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.26 V · Corrosion Resistance 65 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Formability (cold)
Same in both: Machinability Rating (AISI 1212 = 100 %) 30% · Weldability 45 / 100 · Castability 35 / 100 · Brazeability / Solderability 90 / 100 · Polishability 80 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 55 MJ/kg23,646 BTU/lb · Embodied Carbon (primary production) 3.6 kg CO₂/kg · Embodied Water 320 L/kg38.3 gal/lb · Typical Recycled Content 40%
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C41500-H02 vs C41500-H08 — frequently asked
Is C41500-H08 stronger than C41500-H02?
Yes. C41500-H08 has a typical yield strength of 586 MPa (85 ksi) against 400 MPa (58 ksi) for C41500-H02 — about 47% more. Tensile strength is 627 MPa (90.9 ksi) vs 455 MPa (66 ksi).
Which condition does FabDigit quote by default, H02 or H08?
H02 is the default C41500 condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, C41500-H02 or C41500-H08?
C41500-H08. Its machinability rates fair (37/100) against poor (32/100) for C41500-H02.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C41500-H02 and C41500-H08 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.