Copper Alloy C17510-TD02 vs C17510-TH04
Copper Alloy · C17510 temper comparison
C17510-TD02 and C17510-TH04 are two conditions of the same copper alloy grade, C17510: TD02 (solution heat treated and cold worked, half hard) versus TH04 (TD04 and precipitation hardened). The chemistry is identical, so every difference below comes from the condition. C17510-TH04 is the stronger of the two: yield strength 760 MPa (110 ksi) against 415 MPa (60.2 ksi) for C17510-TD02, about 83% more; tensile strength follows at 830 MPa (120 ksi) vs 500 MPa (72.5 ksi). In exchange, C17510-TD02 is the more ductile: elongation 12% versus 8% for C17510-TH04, and C17510-TH04 is harder (250 HB vs 130 HB). C17510-TH04 is stiffer (138 GPa vs 131 GPa) and C17510-TH04 runs hotter in service (340°C vs 150°C continuous). On the shop floor, C17510-TH04 machines more easily (50 vs 35 out of 100).
C17510-TD02Choose it when the part is bent, formed or impact-loaded.
C17510-TH04Choose it when strength drives the design, or when the part sees heat.
C17510-TD02 vs C17510-TH04: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all copper alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Hardness, Rockwell B
Hardness, Vickers
Same in both: Shear Modulus 53 GPa7.7 Msi · Bulk Modulus 115 GPa16.7 Msi · Poisson's Ratio 0.3 · Fracture Toughness (K_IC) 95 MPa·√m86.5 ksi·√in
Physical
Density and transition temperatures.
Density
Same in both: Melting Point (Solidus) 1,000°C1,832 °F · Liquidus Temperature 1,070°C1,958 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Specific Heat Capacity
Max Service Temperature (continuous)
Same in both: Thermal Expansion (CTE, 20–100 °C) 17.6 µm/m·K9.8 µin/in·°F · Min Service Temperature -200°C-328 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.2 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Polishability
Same in both: Castability 45 / 100 · Brazeability / Solderability 70 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Embodied Water
Typical Recycled Content
Strength versus weight
Yield strength against density for every copper alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
C17510-TD02 vs C17510-TH04 — frequently asked
Is C17510-TH04 stronger than C17510-TD02?
Yes. C17510-TH04 has a typical yield strength of 760 MPa (110 ksi) against 415 MPa (60.2 ksi) for C17510-TD02 — about 83% more. Tensile strength is 830 MPa (120 ksi) vs 500 MPa (72.5 ksi).
Which condition does FabDigit quote by default, TD02 or TH04?
A is the default C17510 condition in the FabDigit quote flow (neither TD02 nor TH04). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, C17510-TD02 or C17510-TH04?
C17510-TH04, by a small margin. Both rate fair for machinability — 50/100 against 35/100 for C17510-TD02.
Ready to make it?
Upload a CAD file and FabDigit prices the part in C17510-TD02 and C17510-TH04 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.