Cork Composite Core CR vs Cork Composite Core NL10
Composite · Cork Composite Core grade comparison
Cork Composite Core CR and Cork Composite Core NL10 are two grades of the same composite grade, Cork Composite Core: CR (cold rolled) versus NL10 (low-density cork core). The chemistry is identical, so every difference below comes from the condition. Cork Composite Core CR is the stronger of the two: tensile strength 2 MPa (0.29 ksi) against 0.45 MPa (0.0653 ksi) for Cork Composite Core NL10, about 4.4 times as much. Cork Composite Core CR is the more ductile: elongation 18% versus 12% for Cork Composite Core NL10. Cork Composite Core NL10 is lighter (0.13 g/cm³ vs 0.75 g/cm³ for Cork Composite Core CR) and Cork Composite Core CR is stiffer (0.02 GPa vs 0.01 GPa).
Cork Composite Core CRChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
Cork Composite Core NL10Choose it when weight is the constraint, or when the part sees heat.
Cork Composite Core CR vs Cork Composite Core NL10: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Cork Composite Core CRCork Composite Core NL10
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Tensile Strength (Ultimate)
Elongation at Break
Compressive Strength
Compressive Modulus
Shear Strength
Compression Set (22 h, 70 °C)
Same in both: Poisson's Ratio 0.1
Physical
Density and transition temperatures.
Density
Same in both: Water Absorption (24 h) 6% · Water Absorption (Saturation) 15%
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Limiting Oxygen Index
Same in both: Specific Heat Capacity 1,700 J/kg·K0.41 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 50 µm/m·K27.8 µin/in·°F · Min Service Temperature -60°C-76 °F · Max Service Temperature (short-term) 150°C302 °F
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: UV / Weathering Resistance 40 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 6 MJ/kg2,580 BTU/lb · Embodied Carbon (primary production) 0.5 kg CO₂/kg · Typical Recycled Content 90%
Strength versus weight
Yield strength against density for every composite grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Cork Composite Core CR vs Cork Composite Core NL10 — frequently asked
Is Cork Composite Core CR stronger than Cork Composite Core NL10?
Yes. Cork Composite Core CR has a typical tensile strength of 2 MPa (0.29 ksi) against 0.45 MPa (0.0653 ksi) for Cork Composite Core NL10 — about 4.4 times as much.
Which grade does FabDigit quote by default, CR or NL10?
NL20 is the default Cork Composite Core condition in the FabDigit quote flow (neither CR nor NL10). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Cork Composite Core CR or Cork Composite Core NL10?
Cork Composite Core NL10, by a small margin. Both rate excellent for machinability — 92/100 against 85/100 for Cork Composite Core CR.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Cork Composite Core CR and Cork Composite Core NL10 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.